Advertisement
Quick Links
Advertisement
Summary of Contents for Nordisk Teltbutikk SST304716
- Page 1 Double Truss Shelter Model# SST304716 W9.14xL14.2xH4.88m Assembly Instructions Page 1...
-
Page 2: Recommended Tools
RECOMMENDED TOOLS Equipment List Speed Wrench 22#.23#.24# Hammer (30lb) Rope (12#) Long Tape (50m) Hammer Drill*1 Lifter*2 Crane*1 Forklift*1 Protective equipment Page 2... - Page 3 YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE SHELTER. Thank you for purchasing our shelter. When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the shelter. Please read these instructions before you begin.
- Page 4 Double Truss Shelter W9.14xL14.2xH4.88m Parts List Part Qty/ Description Code Top Truss Arch for middle Top Truss Arch for front and back end (with connection plate) Upper Truss Arch for middle Upper Truss Arch for front end Upper Truss Arch for back end-left Upper Truss Arch for back end-right...
- Page 5 Tube Clip for bracing tube No.5 Bolt M10x50 for tube clip No.10 24+2 Bolt M8x60 for swaged tube of 192+5 truss arch Bolt M8x100 for purlins 88+5 Bolt M8x50 for purlin No.4, 4A, 66+5 Winch for tensioning tube No.8 Knitting Rope for Roof Cover bundle Cable Tie for Roof Cover Belt for winch No.14...
- Page 6 Bolt M8x50 for swaged tube 10+2 Bolt M10x30 for connection plate 20+3 Cable Tie for Back Cover Knitting Rope for Back Cover bundle Stake Peg (normal conditions) Earth Auger with its tool (normal conditions) Expansion Bolt (concrete ground) Front End Panel Portal for front end-right 1 set (2pcs/set)
- Page 7 Knitting Rope for front cover bundle Cable Tie for front cover Stake Peg (normal conditions) Earth Auger with its tool (normal conditions) Expansion Bolt (concrete ground) Steel Wire for front door bundle Steel Wire rope clip for front door Door Track for front door 2 sets (2pcs/set) Bracket for Winch No.37...
-
Page 8: Installation Process
INSTALLATION PROCESS A—BASE PLATES INSTALLATION Please refer to the diagram (Figure 1) to mark the position of base plates The measurement is from center to center of plates. Referring to the diagram and confirm the place of base plates. ENSURE THAT THE FOUNDATION IS SQUARE. 1. - Page 9 Figure 1 Page 9...
- Page 10 B—FRAME INSTALLATION (Arch No.1 to 8) 1. Find Truss Arches for front end (No.1A, 2B, 3A) and Base Plate (No.6) for Arch No.1 and connect them by Bolt M8x60 (No.12). 2. Find relative parts of rails and portals for front end and assemble them referring to Figure 2. Page 10...
- Page 11 3. Find Truss Arches (No.1, 2, 3) for Arch No.2 to 7 and connect them by Bolt M8x60 (No.12). Please refer to Figure 3 for details. Page 11...
- Page 12 4. Find Truss Arches for front end (No.1A, 2A, 3A) and Base Plate (No.6) for Arch No.8 and connect them by Bolt M8x60 (No.12). 5. Find relative parts of rails and portals for back end and assemble them referring to Figure 4. Page 12...
- Page 13 6. Lift the assembled arches onto base plates. 7. When finish installing the first two arches, install Purlin (No. 4). Connect purlins by Bolt M8x50 (No.13A) and connect them to arch by Bolt M8x100 (No.13) and then go to Arch No.3 to No.7 and Purlins (No.4A &...
- Page 14 Page 14...
- Page 15 C-INSTALLING COVER NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A slight breeze is the most advantageous for cover installation. To take advantage of the breeze, pull the cover up over the arches with the breeze blowing in the cover like a sail filled with air. 1.
- Page 16 ROOF COVER INSTALLATION Page 16...
- Page 17 FRONT COVER AND MECHANICAL DOOR INSTALLATION Page 17...
- Page 18 MECHANICAL DOOR INSTALLATION Page 18...
- Page 19 BACK COVER AND PULL EASE ROLL-UP DOOR INSTALLATION Now your assembly is completed. Page 19...