Download
Share
Print this page
  1. Manuals
  2. Brands
  3. komodo Manuals
  4. Spreader
  5. ATVSS350
  6. Owner's manual

komodo ATVSS350 Owner's Manual

350 lbs seeder
Hide thumbs

Advertisement

Quick Links

Download this manual
3
5
0
l b
s
S
e
e
d
e
r / S
p
r
e
a
d
e
r
3
5
0
l b
s
S
e
e
d
e
r / S
p
r
e
a
d
e
r
Owner's Manual
Owner's Manual
Congratulations on your purchase. You have purchased a dependable and sturdy seeder/spreader,
but only by proper care and operation can you expect to receive the service and long life designed
and built into it. This manual contains valuable information about your new Seeder/Spreader. It has
been carefully prepared to give you helpful suggestions for operating, adjusting, servicing and
ordering repair parts.
#ATVSS350

Advertisement

loading

Summary of Contents for komodo ATVSS350

  • Page 1 This manual contains valuable information about your new Seeder/Spreader. It has been carefully prepared to give you helpful suggestions for operating, adjusting, servicing and ordering repair parts. #ATVSS350...

  • Page 2: Table Of Contents

    Keep this manual in a convenient place for quick and easy reference. Study it carefully. If in the future your seeder may need new parts to replace those that are worn or broken, if so, call 1 (800)333-8889 and provide the model, part number, and proof of purchase and we will replace the part as outlined in our Limited Warranty.
  • Page 3 Remove spreader components from box; check that you received all necessary parts. If you are missing a component please call (800)333-8889 for replacement. Attach the tow bar adjustable plank (2) to the frame plate (1), using 4 ea. (M8) Bolts (4), nuts (3), and lock washers (5), as shown.
  • Page 4 Assemble wheels to Spreader using 2 ea. (M8) bolts, flat washers, and lock nuts. Then assemble hopper to spreader base using 3 ea. (M10) bolts (4), nuts (2) and lock washers (5). Fasten heads inside hopper as shown. Assembly wind drift braces (3) using 3 ea. (M8) bolts (2), nuts (4), flat washer (6), and lock washers (5), attach as shown.
  • Page 5 Assemble guide assembly as shown using lock knob (2), guide (3) and square nut (4). Attach levers to feed adjust plates as shown. Attach lever (5) through feed scale mount using 1 ea. (M10) bolt (2), flat washer (16), spring (3), handle washer (4), and lock nut (6).

  • Page 6: Introduction

    The Big Roc Spreader is a standard centrifugal spreader and is used for the distribution of granular fertilizers, seeds, salts, etc. It can be used by most small / medium powered vehicle (ATV, Tractor, Etc.) Thoroughly read this manual before operation of spreader and follow all assembly and maintenance procedures / recommendations to help ensure safe and efficient operation of the spreader.
  • Page 7 Any work of maintenance, adjustment and cleaning must be done with the machine on the ground (stable conditions), turning off the ATV or lawn tractor engine and removing the key. Read carefully the safety labels applied on the machine and follow the instructions. The operator during the period of use, maintenance, repair, handling or storing of the machine must wear accident-prevention shoes and safety gloves.
  • Page 8 The Manufacturer is not responsible for damages caused by an improper and unforeseen use of the machine. The Manufacturer is not responsible for: Improper use of the machine, use by untrained staff; Serious deficiencies in the foreseen maintenance; Changes or not allowed modifications; Use of non-original or specified spare parts;...

  • Page 9: Connections

    For connection of the spreader to the vehicle, follow these steps: With vehicle and spreader on level ground, back vehicle in front of spreader and shut-off engine and set parking brake. Note: it is necessary to have a 1-7/8” ball on the back of the tow vehicle. Make sure hopper is empty, lift coupling and set onto tow ball of vehicle.
  • Page 10 In order to assure equal distribution on both sides of the spreader, depending on the different material specifications, the distributor vanes can be adjusted into varying positions by simply removing the front screw and turning vane, reinstall screw. When all the vanes are in the 1st position, the distribution is increased towards the left, compared to the way the vehicle is moving.

  • Page 11: Maintenance / Storage

    Hopper must be loaded only after having hitched the spreader to vehicle. The operator during the period of use, maintenance, repair, transport or storing of machine, must wear accident prevention articles which may include; shoes, gloves, eye, ear, and breathing apparatus. After following procedures for safety, attaching spreader, and filling hopper, it is possible to begin work.

  • Page 12: Warranty

    Komodo ATV Seed Spreader Limited Warranty KOMODO., (“Distributor”) warrants its ATV SEED SPREADER products (the “Products”) as follows: 1. Limited Warranty. Distributor warrants to original purchaser, providing Proof of Purchase, that the Products sold hereunder will be free from defects in material and workmanship for a period of one year from date of purchase.