Table of Contents
Summary of Contents for MCCI Catena 4612
- Page 1 MCCI Corporation 3520 Krums Corners Road Ithaca, New York 14850 USA Phone +1-607-277-1029 Fax +1-607-277-6844 www.mcci.com Catena 4612/4611 User Manual Engineering Report 234001173 Rev A Date: 2019-03-01 Copyright © 2019 All Rights Reserved...
- Page 2 Additional rights and obligations regarding this document and its contents may be defined by a separate written agreement with MCCI, and if so, such separate written agreement shall be controlling. The information in this document is subject to change without notice, and should not be construed as a commitment by MCCI.
-
Page 3: Table Of Contents
Table 1 Difference between 4612 and 4611 ....................6 Table 2 Antenna Specification ........................9 Table 3 USB to Serial Connection ........................ 13 Table 4 Catena 4612 to STLink connection ....................17 LIST OF FIGURES Figure 1 Catena 4612 ............................ 5... - Page 4 Figure 14 BSP Installation ........................... 15 Figure 15 BSP Installed ..........................16 Figure 16 Catena 4612 connection with PC using STLink Debugger ............16 Figure 17 Catena 4612 connection with ST Link programmer ..............17 Figure 18 Configuration for upload using STLink programmer ..............18 Figure 19 Catena 4612 DFU Mode Connection...................
-
Page 5: Introduction
Catena 4612/4611 User Manual Engineering Report 234001173 Rev A 1 Introduction The MCCI Catena® 4612 and 4611 is a complete single-board IoT device for LoRaWAN™ technology projects. Based on the Murata CMWX1ZZABZ-078, and designed to be compatible with the Adafruit... -
Page 6: Table 1 Difference Between 4612 And 4611
STM32L082 CPU (Cortex M0+, 32 MHz, 192K flash, 20K RAM) High quality RF engineering Certified for US and EU Compatible with IN866, AS923, AU921 bands Figure 2 Catena 4612/4611 Description Integrated sensors Pressure Temperature ... -
Page 7: Additional Features
ST Micro tools may also be used. The Catena 4612 works well with and is tested with The Things Network (an open-source, user- owned IoT network based on LoRaWAN); but can be used with any LoRaWAN-compatible network. 3 Catena 4612/4611 Pinouts... -
Page 8: Hardware Requirements
Catena 4612/4611 User Manual Engineering Report 234001173 Rev A Figure 3 Catena 4612/4611 Pinout 4 Hardware Requirements 4.1 PinHeaders 12-pin & 16-pin male headers (123001009 & 12301011) have a pitch of 0.1” (2.54mm). Figure 4 12-pin & 16-pin Male Headers 4.2 1x04 Screw Terminals... -
Page 9: Antenna
Catena 4612/4611 User Manual Engineering Report 234001173 Rev A Figure 5 1x04 Screw Terminals 4.3 Antenna Whip Antenna, u.FL and SMA Antennas can be used. The antenna specifications are shown in Table 2 Figure 6 Whip Antenna Table 2 Antenna Specification... -
Page 10: Usb To Serial Cable
ST-Link Debugger driver for windows can be downloaded from the link below: https://www.st.com/en/development-tools/st-link-v2.html USB to Serial converter for windows Zadig tool is required for programming Catena 4612 the tool can be downloaded from the link below: o https://zadig.akeo.ie Basic libraries required... -
Page 11: Assembly Instructions
6 Assembly Instructions 1) Catena 4612/4611 board assembling procedures are listed below: a. Attach the 12-pin & 16-pin Male Headers on JP1 and JP2 of Catena 4612/4611 board respectively. i. Solder one or two posts on each strip, to tack the header in place ii. -
Page 12: Figure 10 Catena 4612 With Battery
Catena 4612/4611 User Manual Engineering Report 234001173 Rev A Figure 10 Catena 4612 with Battery (Note: The orange plastic seal from the BME–280 (U1) should be removed for proper operation. This seal is intended for protection during manufacturing) 2) Catena 4612/4611 Serial connection. -
Page 13: Configurations Of Catena 4612
Table 3 USB to Serial Connection Catena4612 (JP1) USB - Serial cable (color) Black D0_RX Orange D1_TX Yellow 7 Configurations of Catena 4612 7.1 Library Installation Catena 4612 simple sketch requires the following libraries: Catena-Arduino-Platform Catena-mcciadk arduino-lorawan arduino-lmic ... -
Page 14: Arduino Ide Setup
3. Next, open the board manager. Tools>Board:...Search for MCCI’s BSPs 4. Install the latest BSP for MCCI Catena STM32 to add support for Catena 4612 in Arduino IDE. 5. MCCI Catena STM32 Boards should be installed from the Boards Manager. -
Page 15: Figure 13 Bsp Search
Catena 4612/4611 User Manual Engineering Report 234001173 Rev A Figure 13 BSP Search Figure 14 BSP Installation - 15 -... -
Page 16: Programming Methods
Catena 4612 programming includes two methods ST-Link 7.3.1 ST-LinK Catena 4612 uses ST-Link V2 programmer for programming the firmware. Below is the connection between 4612 and ST-Link programmer Figure 16 Catena 4612 connection with PC using STLink Debugger - 16 -... -
Page 17: Table 4 Catena 4612 To Stlink Connection
Catena 4612/4611 User Manual Engineering Report 234001173 Rev A Pin configurations of the ST-Link debugger with Catena 4612 are mentioned in Table 4 Table 4 Catena 4612 to STLink connection Catena 4612 ST-Link connection ST-Link 4612 Pin Names Pin Numbers... -
Page 18: Dfu
Figure 18 Configuration for upload using STLink programmer 7.3.2 DFU 1. Program the Catena 4612 using DFU mode, this mode requires Zadig tool the download link is mentioned above. 2. Once the tool is downloaded, BOOT0 and +VDD pins should be Shorted using the jumper wire... -
Page 19: Figure 20 Dfu Mode Example
Catena 4612/4611 User Manual Engineering Report 234001173 Rev A Figure 20 DFU mode Example 3. Now reboot Catena 4612 using USB cable. 4. On the Zadig terminal - Select Options -> List All devices as shown Figure 21 Zadig Device Selection 5. -
Page 20: Figure 22 Zadig Driver Replacement
Catena 4612/4611 User Manual Engineering Report 234001173 Rev A Figure 22 Zadig driver replacement 8. Before uploading the code select the following options from Arduino IDE. TOOLS --> UPLOAD METHOD - DFU" && PROGRAMMER - "STM 32 BOOTLOADER" Figure 23 Configuration for upload using DFU mode Now the Sketch can be compiled and uploaded using DFU mode. -
Page 21: Provisioning Steps
Catena 4612/4611 User Manual Engineering Report 234001173 Rev A 7.4 Provisioning Steps After upload the sketch. Please follow the provisioning steps mentioned in the below link https://github.com/mcci-catena/Catena-Sketches/tree/master/catena4450m101_sensor#provision- your-catena-4450 Note: use platformguid “915decfa-d156-4d4f-bac5-70e7724726d8” 7.5 TTN Registration Steps Please follow the steps mentioned in the below link to create an application in The Things Network https://github.com/mcci-catena/Catena-Sketches/tree/master/catena4450m101_sensor#getting-...
Need help?
Do you have a question about the Catena 4612 and is the answer not in the manual?
Questions and answers