Adjusting The Offset Magazine - AEG CFN90 Original Instructions Manual

supply line and fittings are required.

ADJUSTING THE OFFSET MAGAZINE

See figure 7 - 8.
The EZ Load™ feature is designed for quick and easy
reloads. To prevent jamming, always adjust the magazine
to the correct position for the size nail you are using.
There is an adjustment indicator inside the magazine to
help you choose the right position.
To adjust the magazine, pull up on the spool and rotate
it until the nail tray rests in place in the desired position.
Rotate it counterclockwise to lower the nail tray. Turn it
clockwise to raise the nail tray.
Position
Position 1
Position 2
Position 3
Position 4
LOADING THE TOOL WITH NAILS
See figure 9 - 11.
The tool's driving mechanism may cycle when the tool
is first connected to the air supply. Always connect the
tool to the air supply before loading nails to prevent
injury from unintended cycling. Always make sure the
tool's magazine is empty at the beginning of each work
session, before connecting to an air supply.
Keep the tool pointed away from yourself and others
when loading nails. Failure to do so could result in
possible serious personal injury.
Use only the nails recommended for use with this
tool. The use of any other nails can result in tool
malfunction, leading to serious injuries.
Never load nails with the workpiece contact or trigger
activated. Doing so could result in possible serious
personal injury.
The EZ Load™ feature is designed for quick and easy
reloads. There are indicators inside the magazine for
each of the nail sizes the tool will accommodate.
1. Connect the tool to the air supply.
2. Press down on the feeder cover latch and open the
cover. The magazine is on a swing-out mechanism
that will automatically open for easy loading.
3. Adjust the offset magazine for the nail size you are
using.
4. Slide the coil of nails onto the spool with the nail
Nail size
38 - 45 mm
50 - 65 mm
70 - 75 mm
80 - 90 mm
WARNING
WARNING
WARNING
WARNING
points down. Uncoil about 7 cm of nails from the coil
of framing nails.
5. Close the magazine. The feeder cover should remain
open.
6. Insert the first nail into the nail chamber. The first nail
should sit in the nose of the tool.
7. Position the second nail between the guides. The nail
heads should lie in the track.
8. Securely close the feeder cover, snapping it into
place. Be sure that the feeder cover is locked before
resuming operation.
USING THE SELECTABLE TRIGGER
See figure 12 - 13.
Never wedge or hold back the workpiece contact
mechanism during operation of the tool. Doing so
could result in possible serious injury.
This tool is shipped from the factory with a selectable
trigger set in the single sequential actuation mode. The
selectable trigger can also be set for contact actuation
mode.
Note: Do not use this tool in the contact actuation mode
unless you have had training in the use of this mode of
operation. Untrained or inexperienced operators should
not use the contact actuation mode.
SINGLE SEQUENTIAL ACTUATION MODE
Single sequential actuation provides the most accurate
fastener placement.
1. Disconnect the tool from the air supply.
2. Depress the trigger lever pivot pin.
3. Rotate the selector to position A.
4. Release the trigger lever pivot pin.
The nailer will not function properly if the selector is
not securely seated in either position A or B. Always
assure the selector is seated properly to avoid an
unexpected fastener discharge and possible serious
personal injury.
5. Reconnect the tool to the air supply.
6. Grip the tool firmly to maintain control. Position the
nose of the tool onto the work surface.
7. Push the tool against the work surface to depress the
workpiece contact.
8. Pull the trigger to drive a fastener.
9. Allow the tool to recoil away from the work surface as
the fastener is driven.
CONTACT ACTUATION MODE (BUMP FIRE)
Contact actuation allows very fast repetitive fastener
placement.
1. Disconnect the tool from the air supply.
2. Depress the trigger lever pivot pin.
3. Rotate the selector to position B.
4. Release the trigger lever pivot pin.
WARNING
WARNING
6