Advertisement
ORIGINAL INSTRUCTIONS
S/N: 1476 AND ABOVE
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
GB50
PNEUMATIC INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
+1 (586) 226-1500
Clinton Twp. MI 48038 USA +1 (586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com
Advertisement
Table of Contents
Summary of Contents for Gage Bilt GB50
- Page 1 S/N: 1476 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GB50 PNEUMATIC INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court +1 (586) 226-1500 Clinton Twp.
-
Page 2: Table Of Contents
Setting stroke - .740" (18.8mm) Noise level - 81.5 dB (A) Rated pull load - 600 lbs. (2.67kN) Vibration - Tested– No hazards found. GB50 S/N: 1476 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 5/15... -
Page 3: Warnings
Tool is not to be used as a hammer. WARNING Air pressure not to exceed 100 psi. (6.9 bar) , except where noted. GB50 S/N: 1476 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 5/15... -
Page 4: Principle Of Operation And Air Exhaust
(Side of tool) Rear Exhaust Port Plugged OPTIONAL Air is exhausted through EXHAUST Rear Exhaust Port (Rear of tool) Rear Exhaust Port Plug removed GB50 S/N: 1476 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 5/15... -
Page 5: How To Use The Gb50
8. Always hold tool so pulling head is perpendicular to surface of material in which rivet is being installed. Exert firm pressure against rivet during installation. WARNING: Always disconnect air supply when tool is not in use to prevent accidental start-up. GB50 S/N: 1476 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 5/15... -
Page 6: Description And Maintenance
The GB50 Riveter is 7.31" (185.7mm) high, has a .740” (18.8mm) stroke and generates a minimum of 600 lbs. (2.67kN) of pull at 90 psi (6.2 bar). It operates from 90 psi (6.2 bar)-100 psi (6.9 bar) of air pressure at the tool. -
Page 7: Parts Lists
510125 Dowel Screw 510215 Handle 510322 Actuator 510107 O'Ring 400772 Button Head Screw A-819 Slotted Pin 400607 Lever Assy 551129 (includes slotted pin 400607) GB50 S/N: 1476 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 5/15... -
Page 8: Nose Assembly Selection Chart
CHERRYM AX® AND M BC® ARE REGISTERED TRADEM ARKS OF CHERRY AEROSPACE. FASTACK® AND SUPERTACK® ARE REGISTERED TRADEM ARKS OF ALLFAST FASTENING SYSTEM S INC. GAGE BILT CERTIFIES THE GB50 WILL INSTALL THE ABOVE FASTENERS 1) RIGHT ANGLE NOSE ASSEMBLYS MAY REQUIRE MORE THAN ONE PULL. -
Page 9: Eu Conformity And Warranty
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB50 FASTENER INSTALLATION TOOL This product specified above conforms to the above dIrectives and standards.
Need help?
Do you have a question about the GB50 and is the answer not in the manual?
Questions and answers