Summary of Contents for Ritter Amplification Camper 212 GFR Speaker Kit
- Page 1 Installation instruction Ritter Amplification Camper 212 GFR Speaker Kit www.ritteramps.com...
-
Page 2: Table Of Contents
Table of content : 1. Introduction 2. Preparation 3. Recommended tools 4. Let's start 5. Installation of the back plate 6. Wiring the speakers 7. Applying the new label on the terminal plate (option ) 8. Congratulations ! www.ritteramps.com... -
Page 3: Introduction
1. Introduction Thank you very much for purchasing the Camper 212 kit ! With this kit you will be able to build your own high quality guitar flat response speaker cabinet. The Camper 212 cabinet is designed for the use with guitar profiling or modelling gear, where the speaker profile / model will remain part of the overall sound experience. -
Page 4: Preparation
2. Preparation To install the kit into the Palmer 212 unloaded open back ! cabinet you will need some basic mechanical skills, several tools and some work space. If you feel you do not have the tools, the skills or the work space, please do not attempt to install this kit yourself. - Page 5 – terminal plate label www.ritteramps.com...
-
Page 6: Recommended Tools
3. Recommended tools short screwdriver Philips 2 (PH2) or – cordless screwdriver If you want to apply the new label on the terminal plate, you will need some : – paper towels – technical alcohol – a little bit of water –... -
Page 7: Installation Of The Back Plate
5. Installation of the back plate If you haven’t done already, please remove dust and splinters from the inside of the cabinet now. – Put the mounting plate into the Palmer cabinet first. – Put the back plate into the Palmer cabinet secondly. www.ritteramps.com... - Page 8 www.ritteramps.com...
- Page 9 – Push the back panel into the opening of the Palmer cabinet. – Press the mounting plate to the inner wall of the cabinet and align it to the back plate. – Use the markings we made on the back plates inner surface to align both plates to each other.
- Page 10 Once the mounting plate is aligned with the markings on the back side of the back plate, screw in the first two 25mm chipboard screws. I recommend to start with the vertically aligned two screws in the middle of the mounting plate.
- Page 11 You can tighten the screws in the order shown below : You will need a short PH2 screwdriver or cordless screwdriver to be able to tighten the screws 3-14. Tighten all screws until there is no gap left between the mounting plate and the inner back side of the cabinet and the back plate is in place.
-
Page 12: Wiring The Speakers
6. Wiring the speakers Reinstall the terminal plate Put the Palmer cabinet on it's back side place the first speaker ion the right side of the baffle. Connect it`s terminals with the cable, coming from the right side of the terminal plate as shown below. Connect the copper coloured wire to the and the silver coloured wire to the –... -
Page 13: Applying The New Label On The Terminal Plate (Option )
Align the speakers to the holes and use the provided screws to tighten them. 7. Applying the new label on the terminal plate (optional) I think it is a good idea to apply the new sticker to the former back side of the terminal plate. - Page 14 Prepare some water, a piece of soup or liquid soap, a squeegee and the new label. Damp the soap with some of the water and cover the complete surface of the terminal plate with a thin film of soaped water. Peel the white paper backing off the sticker.
-
Page 15: Congratulations
Slowly lower the sticker onto the surface and rub it in place firmly with a squeegee or credit card. Rub the sticker until no soap water is pressed out of the area between the sticker and the plate. If the sticker moves, you can hold it in place by sticking one fingertip into on of the jack holes.
Need help?
Do you have a question about the Camper 212 GFR Speaker Kit and is the answer not in the manual?
Questions and answers