Summary of Contents for XENIA SCD-7000
- Page 1 XENIA SCD-7000 ETR AM/FM/MPX, 4CH-HIGH POWER IN DASH 5 CD CHANGER WITH FLIP DOWN FULL FRONT DETACHABLE PANEL...
-
Page 2: Table Of Contents
INDEX - Installation.........… 3 - Connection........5 - Basic Operation......6 - Radio Operation......… 9 - CD Changer Operation.....11 - Trouble Shooting......14 - Care and Maintenance....15 - Specification......16... -
Page 3: Installation
INSTALLATION Disconnect Battery Prepare Radio for Installation Before you begin, always Remove transport screw (you can not disconnect the battery insert a CD until the screw is removed.) negative terminal. Install Half-sleeve Not needed for ISO-DIN installation. Half-sleeve Support Strap (supplied) (supplied) 1. - Page 4 Final Installation 1. Slide radio chassis into half-sleeve. 2. Secure to strap using nut if possible. 3. Reinstall any items you removed from the dashboard Bolt (supplied) Final Installation-ISO-DIN. 1. Remove trim ring from front of radio. 2. Mount factory brackets on new radio using existing screws from old radio. 3.
-
Page 5: Connection
CONNECTION – Wiring Diagram If you are installing new speakers or amplifiers of replacing an aftermarket installation, Use this diagram. Color Function White/black LF- Speakers White LF+ Speakers Green/black LR- Speakers Green LR+ Speakers Gray/black RF- Speakers Gray RF+ Speakers Violet/black RR- Speakers Violet... -
Page 6: Basic Operation
BASIC OPERATION (3),(4),(5),(6),(7),(8) (14) (11) (12) ( 9 ) (13) (10) (1) POWER ON- OFF BUTTON (PWR) Press this button to turn the unit on or off. When the ignition switch is "on", the unit will turn on automatically if the CDC/BAND/AUX buttons are pressed. (2)AUDIO (LEVEL) CONTROL (VOLUME +/-) To increase the volume level, turn the VOLUME +/- knob clock-wise (+ direction). - Page 7 counter-clockwise to decrease the bass response or clockwise to increase it as desired. The level will be shown on the display panel from a minimum B-6 to maximum of B +6. (B 0 indicates flat response) The display will automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated.
- Page 8 SETTING THE CLOCK 1.Switch the vehicle ignition. 2. Press and release the Time/Frequency button to access the time display; then press and hold the T/F button until the time colon begin to flash. 3. With the time colon flashing, press the Down Tuning ( ) button to adjust the hours or the Up Tuning ) button to adjust the minutes indication to the correct time.
-
Page 9: Radio Operation
RADIO OPERATION ¨ è ¨ é ¨ ê ¨ ë ¨ ç AM/FM BAND SELECTOR (BAND) During radio operation, each time this button is pressed, the radio band is changed. The indication AM I, AM ¥ ± , FM¥ ° , FM¥ ± or FM¥ ² will appear on the display panel according to your selection. During disc play, pressing this button will stop play of the disc and switch to radio operation. - Page 10 ¨ ê PRE-SET SCAN (PS) / AUTO-STORE TUNING (AS) Press this button momentarily to scan the stations pre-set into each AM band and each FM band. The unit will stop at each pre-set station for 10 seconds before continuing to the next pre-set station (the pre-set station number on the display panel will flash during Pre-Set Scan operation).
-
Page 11: Cd Changer Operation
CD CHANGER CONTROL ¨ ë ¨ í ¨ ô ¨ ì ¨ î ¨ ï ¨ ð ¨ ñ ¨ ò ¨ ó ¨ õ DISC INF ¨ ç DISC SLOT With the front panel in the fold-down position, gently insert the disc into the slot (label surface facing up) until the soft-loading mechanism engages and pulls the disc in. - Page 12 ¨ è Loading CDs Insert a disc in to the slot. The disc number is shown on the display. To insert more discs, repeat the above procedure. Flip the panel up to close. The display will show "cd-in". Press the CDC button to begin the play. ¨...
- Page 13 ¨ ï REPEAT PLAY SELECTOR During disc play, press this button to repeat the play of the selected track (RPT will appear on the display panel). Play of the track will continue to repeat until the button is pressed again and the RPT indication disappears from the display panel.
-
Page 14: Trouble Shooting
TROUBLE SHOOTING Problem Cause Corrective Action No power to yellow wire Check connection Does not operate No power to red wire Check vehicle fuse (display does not light) Inline fuse blown Replace fuse No speakers operate Speaker harness not connected Connect speaker harness (display lights normally) Incorrect splices or connections... -
Page 15: Care And Maintenance
CARE AND MAINTENANCE The radio portion of your new sound system does not require any maintenance. We recommend you keep this manual for reference to the any features found in this unit as well as how to set the clock. The compact disc player section also requires no routine maintenance, but proper understanding of its use and handing will help you obtain maximum enjoyment of its capabilities. -
Page 16: Specification
l Do not stick paper, tape, or labels on the disc surfaces nor write on them with any type of marker. SPECIFICATIONS Size: 178(W) x 166(D) x 50(H) Operating Voltage: 12 Volts DC, Negative Ground. Output Power: 160Watts Maximum (40Watts x 4 Channels) Output Wiring: Floating Ground Type Designed for use with 4 Speakers (Front and Rear Channels Cannot be combined (Bridged) for use with 2 Speakers)