Axminster Craft AC16BM Original Instructions Manual

Axminster Craft AC16BM Original Instructions Manual

Bench morticer

Advertisement

Quick Links

Code 105114
Original Instructions
AC16BM
Bench Morticer
AT&M: 21/03/2019
BOOK REF : 105799

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AC16BM and is the answer not in the manual?

Questions and answers

Summary of Contents for Axminster Craft AC16BM

  • Page 1 Code 105114 Original Instructions AC16BM Bench Morticer AT&M: 21/03/2019 BOOK REF : 105799...
  • Page 2: Eu Declaration Of Conformity

    06/42/EC - Annex I/05.2006 EN 61029-1:2009 Type Bench Morticer Model AC16BM and conforms to the machinery example for which the EC Type-Examination Certificate No AN 50171993, AM 50171994 has been issued by Laizhou Tongtailai Machinery Co., Ltd. Signed at: No. 2666 Shuangfeng Road Chengguo Dongfeng Laizhou, Shandong 261437 China and complies with the relevant essential health and safety requirements.
  • Page 3: What's Included

    What’s Included Quantity Item Part AC16BM Bench Morticer Operating Lever Saddle Operating Wheel Operating Wheel Shaft Distance Stop Rods Bag 1 M6 x 30mm and M6 x 16mm Lift and Shift Handles Ring Collar Clamps with Lift and Shift Handles...
  • Page 4: General Instructions For 230V Machines

    General Instructions for 230V Machines The following will enable you to observe good working • Leave machine unplugged until work is about to practices, keep yourself and fellow workers safe and main- commence. • Always disconnect by pulling on the plug body tain your tools and equipment in good working order.
  • Page 5 Assembly Please take some time to read the section entitled there is adequate room on either side for the size of timber “Illustration and Parts Description” to identify the you plan to use. Once you are happy bolt the morticer various parts of your machine so that you are familiar down.
  • Page 6 Assembly Locate the operating wheel (B), slide it on to the operating Secure using the phillips screw and clamping washer you wheel shaft (C) as shown in fig 6 (Note: Make sure the removed earlier (See fig 7). locating key engages into the shafts machined slot). Fig 7.
  • Page 7: Specification

    Specification Code 105114 Centre of Chisel to Back Fence 70 mm Model AC16BM Max Height of Timber with 12.7mm Chisel and Bit 110 mm (160 mm with optional spacer block) Rating Craft Max Chisel Size Softwood Power 16 mm 375 W...
  • Page 8 Illustration and Parts Description Lift and shift handle lock Transverse gib strip adjusters Table gib strip adjusters Table fine feed control knob Door catch Auger mounting chuck Chuck door securing screw...
  • Page 9 Illustration and Parts Description Locking bolt Operating lever Motor Chuck access door Lift and shift handle lock Headbox gib strip adjusters Table clamping assembly Table Headbox support column Gas powered head return strut Base casting Fence Distance stop assembly...
  • Page 10: Setting Up The Machine

    Setting Up the Machine Initial Set up Introduce the chisel into the adaptor collar, press the the chuck key. Gently pinch the chisel in place by finger auger up into the chuck, tighten the chuck and withdraw tightening the clamping bolt. (See figs A,B) Fig A.
  • Page 11 Setting Up the Machine Setting the chisel auger clearance Fig C. General Notes require. Pull the headbox down, and put the end of the timber against the chisel, position the headbox so that the The mortise will generate a lot of ‘grip’ on the chisel, chisel points or the auger point are at the depth required, especially the first cut, or if the timber is a little green.
  • Page 12 Setting Up the Machine Depth Stop Assembly The hinged depth stop can be using to adjust the depth of the morticer (See fig A). The ring collar clamp can also be used as a depth stop (See fig B). Fig A. Fig B.
  • Page 13 Setting Up the Machine Table Clamp Assembly The table camp can be adjusted to accommodate different which slots into the centre holes in the table to prevent sizes of timber using the pre-drilled holes in the table (See movement (See figs 13 and 14). The clamp can also be figs 13,15 and 16).
  • Page 14: Optional Accessories

    Optional Accessories Headbox support column Spacer Block Assembly (Order no: 950175) M10 x 74mm bolts Drill Chuck and Adaptor (Order no: 400287) You can turn your morticer into a pillar drill by attaching a drill chuck and adaptor.
  • Page 15: Maintenance

    Maintenance There is very little maintenance required on your morticer. Keep it clean Once a month Make sure the rack and pinion gears do not become Blow/suck the motor to remove any debris that might clogged with chips/sawdust. have lodged in the fan cover. Lightly spray oil on all exposed metal surfaces if the Oil the chuck and exercise it over its full range to ensure machine is going to stand idle for any length of time.
  • Page 16 Exploded Diagrams/Lists...
  • Page 17 Exploded Diagrams/Lists Part No. Description Part No. Description Operating Leaver Motor Handle Screw Switch Box Screw Handle Screw Rack Operating Shaft Sliding Plate Screw Screw Drift Handle Screw Screw Setting Collar Gas Spring Guide Column Screw Screw Washer Localiser Gear Screw Bolt Cover...
  • Page 18 Notes...
  • Page 19 Notes...
  • Page 20 The Axminster guarantee is available on Craft, Trade, Engineer, Air Tools & CNC Technology Series machines Buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years! For more information visit axminster.co.uk/3years The packaging is suitable for recycling.

Table of Contents