Advertisement
Use Direct Coil/Side Coil to heat nuts/bolts, screws etc. fig.3. Keep gap of 3/4mm between coil and object being heated. Do Not reuse
bolts as heat may have effected the physical properties of the bolt.
6. Pad Coil Ø55mm
Use Pad coil for heating of sheet steel to assist with the removal of decals, stickers, sealants/putties, use the coil approximately 5mm
away from the surface of the steel sheet.
WarninG! over heating will damage painted surfaces. no liability will be accepted for damage caused by improper use.
‰
7. flex coil 740mm
use flex coil when it is not possible to use direct coils due to space, or position of object to be heated. can be used on exhaust pipes
and suspension parts, by wrapping the coil around the part before connecting to the torch.
4.
operation
4.1.
Connect the torch to the two output connections on the control panel fig.1 C/D.
4.2.
connect the power supply to the heater using the input power cable, ensure correct power supply is used.
4.3.
select the required torch head and slide into the end of the handle at required angle and tighten the holding screws.
4.4.
Select the desired timing function if required, place coil over fixing or panel to be heated and switch on the machine. Operate the
trigger and the fixing/panel will get hot.
4.5.
the machine has a protection circuit installed to prevent overload in terms of voltage, current and heat. if the pre set value are
exceeded the machine will stop working automatically, until the condition of the machine reverts to normal.
4.6.
The machine is fitted with a fan to keep it cool, ensure that the vents are not covered and there is adequate ventilation. Allow at least
0.3m of free space around the machine.
4.7.
do not over load the heater. do not exceed the duty-cycle, excess current will damage the heater.
4.8.
if the duty cycle is exceeded the heater will stop working for its own protection. the red light will be lit, do not switch heater off or
remove plug from socket as the internal fan will continue to run and cool the heater down. When the red light turns off heating can
continue.
4.9.
if the user has some metal on their person such as coins, jewellery or surgical implants etc. they must avoid the metal item getting
close to the heater torch or torch head, to avoid damage by induction heating.
5. Maintenance
WarninG! Before maintenance and any repair, the power supply must be turned off and the plug removed from the socket.
‰
5.1.
remove dust by using clean dry compressed air regularly, if operating in a dusty environment this should be done on a daily basis.
5.2.
check cables, torch and torch heads for any sign of damage, if any part of the heater is damaged replace or repair. if in doubt contact
a qualified electrician.
5.3.
Avoid water and steam entering the machine, if this happens disconnect from power source and allow to dry, do not use unless it has
been checked by a qualified electrician.
5.4.
if not in use the machine and attachments should be stored in a dry, childproof area.
parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Weee regulations
dispose of this product at the end of its working life in compliance with the eu directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMportant: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
Removal of Decals from sheet steel
sole uK distributor, sealey Group.
Kempson Way, Suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7AR
Original Language Version
01284 757500
01284 703534
VS230 | Issue 1 28/06/16
fig.4
www.sealey.co.uk
sales@sealey.co.uk
Advertisement
