Table of Contents
Advertisement
Quick Links
This gun rack is supplied with brackets to mount it to the 1 ¾" or 2" roll bar on your UTV.
Your guns will be suspended between two roll bars. Crosswise or lengthwise in the top of the canopy and across the cage in front of the steering wheel
are the most widely used mounting areas.
Parts Furnished:
1) 40" tube with hole in 1 end
1) 24" tube with hole in 1 end
4) Roll Bar Half-Clamps
1) Spacer for ¾" tube
4) ¼" x 1 ¾" Bolt
2) ¼" x 2 ¾" bolt
6) ¼" Lock nut
8) 5/32" Allen head set screws
3/32" Allen wrench to tighten set screws
SBB-G gun bracket set (one or two depending on model purchased)
Tools Required:
7/16" wrench and/or socket
1. Pick your spot. Hold your weapon up in desired area to confirm barrel/butt side clearance and front to back location. Note: The Sky Bar outer tube is
40" long. If this is too long for your spot you can cut the necessary amount off the end that does not have the mounting hole drilled.
2. Using a ¼ x 1 ¾" bolt, attach two half clamps loosely to the 1" Sky Bar tube. (Use hole B) See Fig. 1.
3. Partially insert set screws into the foam padded gun brackets. Do not tighten. Slide gun brackets on the 1" Sky Bar tube. See Fig. 9
4. Insert a ¼" x 1 ¾" bolt through the half clamps, ¾" tube and spacer so there is a half clamp on each side of the tube. See Fig. 2.
5. Put the Sky Bar in position and place the half clamps on either side of your roll bar and insert a ¼ x 1 ¾" bolt through the pre-drilled holes.
(Use hole A) Tighten just enough so the clamps will stay on the roll bar. Repeat on the other end of the Sky Bar. (Fig. 3 & 4)
6. Tighten the bolts through the Sky Bar tubes snugly (hole B), making sure all parts are aligned straight between your roll bars.
7. Tighten the bolts (hole A) on the half clamps until there is no movement on your roll bar.
8. Position gun brackets to best fit your weapon(s) and secure with the set screws.
9. Put your weapon in the gun rack and adjust the gun brackets if necessary for the best fit.
25-A Shawnee Way
Bozeman, MT 59715
Fed ID 81-0414516
PH 406-586-9393
SkyBar Mount for UTV with 1 ¾" – 2" Roll Bar
Standard Mount (optional mount on page 3)
FAX 406-585-7378
1
Advertisement
Table of Contents
Summary of Contents for Big Sky Racks SkyBar
- Page 1 PH 406-586-9393 FAX 406-585-7378 SkyBar Mount for UTV with 1 ¾” – 2” Roll Bar Standard Mount (optional mount on page 3) This gun rack is supplied with brackets to mount it to the 1 ¾” or 2” roll bar on your UTV.
- Page 2 UTV Bracket for 1 ¾”-2” Roll Bar ¾” Tube 1” Tube Spacer Fig. 1 Fig. 2 1” Tube ¾” Tube Spacer Fig. 3 Fig. 4...
- Page 3 PH 406-586-9393 FAX 406-585-7378 SkyBar Mount for UTV with 1 ¾” – 2” Roll Bar (for UTV’s with canopy or crossbars that interfere with the standard mounting) This gun rack is supplied with brackets to mount it to the 1 ¾” or 2” roll bar on your UTV.
- Page 4 Hanging your Sky-Bar beneath your Roll Bar. Fig. 5 Fig. 6 Fig. 7 Fig. 8...
- Page 5 Parts for Sky Bar on UTV Roll Bar ¼ x 1 ¾ Bolts ¼ x 2 ¾ Bolts Spacer for ¾” Tube Set Screws Roll Bar Half-Clamps Fig. 9...
- Page 6 RESPONSIBILITIES: If you have notified us of a defect prior to the expiration of the respective warranty period and after shipment to Big Sky Racks, Inc. inspection uncovers a defect that is covered by this Warranty, Big Sky Racks, Inc. will either repair or replace the product at its election. The repaired or replacement product will be returned at Big Sky Racks, Inc.
Need help?
Do you have a question about the SkyBar and is the answer not in the manual?
Questions and answers