Summary of Contents for Legacy SINGLE DROPSIDE CRIB
Page 1
LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 INGLE ROPSIDE JCHE.p65 AYBED WITH RAWER AND 21021 IDDEN ARDWARE CHILD CRAFT INDUSTRIES, INC. P.O. Box 444, Salem, IN USA 47167-0444 PH: 812-883-3111 - FAX: 812-883-1819 - http://www.childcraftind.com A S S E M B L Y D I R E C T I O N S A N D P A R T S...
Page 2
Hardware Bag may contain extra fastening devices. Check quantities and match to Hardware Bag and Carton Parts Lists. If a part is missing or broken contact your dealer or Legacy, 812/ 883-3111, (FAX 812-883-1819), http://www.childcraftind.com for a replacement part or instructional literature.
Page 3
LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 Mount an End Plate - Right N N N N N and an End Plate - Left M M M M M to ends of each Stabilizing 2 - D 2: A IAGRAM SSEMBLY OF TABILIZING Bar V V V V V using (4) Pan Head Machine Screws I I I I I and (4) Lock Nuts G G G G G in each Stabilizing Bar V V V V V exactly as shown.
LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 4 - D 4: A While Footboard Z Z Z Z Z is in a horizontal position place a Stabilizing Bar V V V V V over an installed extended IAGRAM TTACH TABILIZING Screw A A A A A being careful to place End Plate M M M M M &...
Page 5
LH02704: 04/00 LH02704: 04/00 LH02704: 04/00 LH02704: 04/00 LH02704: 04/00 6 - D 6: I IAGRAM NSTALLATION OF ROPSIDE PREPARATION FOR INSTALLATION OF DROPSIDE: II II II II II. Engagement Loosen the four Slotted/Phillips Screws A (Dropside of Metal Top only) which attach the Stabilizing Bar V to the Headboard Track and A A and Footboard Z to prepare for Dropside X X X X X...
Page 6
LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 Read this entire step before starting the procedure to select a Spring W W W W W 7- D 7: A IAGRAM TTACH PRING height position and to attach Spring W W W W W to the Stabilizing Bars V V V V V .
Page 7
LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 LH02704:04/00 8 - D 8: D & I Installation of Mini Blocs E E E E E . Refer to Diagrams 8A 8A, 8B 8B, 8C IAGRAM RAWER UILD NSTALLATION 8D, and 8E 8E. Install (1) Mini Bloc E E E E E into each of the Drawer Ends b b b b b as shown in Diagram 8A 8A.
Page 8
NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE. •STORAGE AND USE OF YOUR LEGACY CRIB: A printed plastic pouch is attached to the crib spring for the permanent storage of the assembly directions.
Page 9
Φ Φ Φ Φ Φ BEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR SHARP EDGES. DO NOT USE CRIB IF ANY PARTS ARE MISSING OR BROKEN. ASK YOUR DEALER OR LEGACY, P.O. BOX 444, SALEM, IN 47167-0444 USA (812/883- 3111), http://www.childcraftind.com FOR REPLACEMENT PARTS AND INSTRUCTIONAL LIT- ERATURE IF NEEDED.