Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for eKoral Lite
Summary of Contents for eKoral Lite
- Page 1 eKoral Lite User Manual 2020...
- Page 2 ...
-
Page 3: Table Of Contents
4.2. eK Power Lite 4.2.1. Pairing (in-app) 4.3. eK Probes 4.3.1. Calibration 5.0. I f/Then Rules 6.0. S chedule 6.1. eK Lite 6.2. Toggles 7.0. S cene 8.0. R esetting the eK Lite... - Page 4 9.0. C onnecting to eKoral Sync Supported Third-Party Devices 9.1. Identifying eKoral Sync Products 9.2. Connecting an eKoral Sync Device to your eKoral Account 10.0. F ail-safe 11.0. F igures...
-
Page 5: Creating An Ekoral Account
Once downloaded, please open the eKoral app and create an account using your email address or Facebook account. Please note that t here are two settings w hen you are creating an eKoral account. These are as follows: 1.1. -
Page 6: Ek Power Lite
■ Max Output: 1 650W - 2000W ■ Cable length: 1 .5m (5ft) 2.3. eK Probe Holder Description: ★ Tempered plastic probe organizer ★ Holds four (4) eKoral probes 2.4. pH Probe Description: ★ Laboratory-grade pH probe, treated to prevent corrosion ★ Specifications : ■... -
Page 7: Safety Precautions
3.0. Safety Precautions When using the eKoral Lite system, as is the case for all electronic equipment operated around water, it is essential to take steps to maintain the integrity and functionality of the devices. Standard precautions should be taken to minimize risks : 1. -
Page 8: Online Pairing (Soft Ap)
WiFi. 1. Log into the eKoral app. On the homepage, click on the “ +” button at the bottom of the screen. You will be able to select which device you wish to pair. Select the eK Lite (... -
Page 9: Ek Power Lite
[eKoral-SERIAL NUMBER]. 3. Plug in your eK Power Lite and press down on the power button at the top of your power bar. Wait for the LED light to flash blue. Once it begins to do so, you can tick the confirmation box in the app and tap ... - Page 10 1. Click “ D evice ” on your eK Lite homepage, and select “ p H ’ ’. At the bottom of the screen, you will find the calibration tab. If you have calibrated before, they will show the last date and time in which you successfully calibrated (...
-
Page 11: If/Then Rules
Sync or the eK Power Lite. 3. Select the “ Then’’ tab. This is when you now select either the eK Power Lite or eK Doser. Out of the selection choose which output would best rectify the situation that will be in place for this rule e.g. -
Page 12: Toggles
2. Select the device you wish to pair. In this case, it is the eK Power Lite. Note: to connect the eK Power Lite to the eK Lite, you will need to connect directly to the eK Lite’s hotspot network. - Page 13 2. Get the reset pin and locate the reset hole on your device. On the eK Lite, it is on the side by the power source. (...
- Page 14 1. Run-time protection : puts a time limit on the execution of a rule as a fail-safe against equipment failure. If the “ IF” clause is repeatedly triggered, it will limit the run-time to the preset value. 2. Lock-out time : the amount of time before a rule can be executed again after run-time protection is triggered.
- Page 15 11.0. Figures 4.1.1. eK Lite Pairing...
- Page 16 4.1.2. Troubleshooting...
- Page 17 4.2.1. eK Power Lite Pairing (in-app)
- Page 18 4.3.1. Probe Calibration (eK Lite)
- Page 19 5.0. eK Lite If/Then Rules...
- Page 21 6.1. eK Lite Schedule...
- Page 22 6.2. Toggles Schedule...
- Page 23 7.0. Scene (eK Lite)
- Page 24 8.0. Resetting (eK Lite)
- Page 25 9.1. Identifying eKoral Sync Products...
Need help?
Do you have a question about the Lite and is the answer not in the manual?
Questions and answers