I2SE XPL Rail 2M E1200 User Manual

User manual XPL Rail 2M – E1200
All rights reserved. This operating instruction may not be reproduced in any way, whether in whole or in part, or copied or
processed using any electronic, mechanical or chemical method without the prior written approval of the publisher.
Any information in this document has been compiled with great care, but may not be deemed an assurance of product
characteristics. in-tech smart charging shall be liable solely to the degree specified in the terms of sale and delivery.
Distribution and reproduction of the documentation and software supplied with this product and the use of its content is
subject to prior written approval by in-tech smart charging.
in-tech smart charging reserves the right to make changes due to technical progress.
Brands
®
HomePlug is a registered trademark of HomePlug Powerline Alliance.
All other names mentioned may be trademarks or registered trademarks of their respective owners. in-tech smart charging
reserves the right to modify the mentioned data without notice and assumes no liability for technical inaccuracies and/or
omissions.
in-tech smart charging GmbH
http://smartcharging.in-tech.com
Friedrich-List-Platz 2
Effective: Rev. 2, April 23, 2020
04103 Leipzig
Germany
Your XPL Rail 2M – E1200
Thank you very much for your trust. We are happy that you have choosen an XPL Rail device. With only a few steps your
device is ready for use and can perform your communication applications.
Notes regarding this manual
Please read this manual carefully before commissioning your XPL Rail device. Keep this manual for later reference.
Please note that product pictures might differ due to a change of our company name and logo.
The manual is to be considered as a part of the device and has to be passed together with it if you hand it to other persons.
Used Symbols:
Attention! A hazard is pointed out.
Proper Use
The device is connected to the mains supply network. The applicable standards and guidelines of the specific country are
to be fulfilled while planning and installing. The device may only be operated in 230V/50Hz and 110V/60Hz mains circuits.
Only electrically qualified persons are allowed to work on mains circuits. The usual regulations for prevention of accidents
are to be followed. To prevent electrical shock you have to disconnect mains from the circuit you are working on. Not
following those installation instructions may lead to fire or danger for life.
Do only operate the device indoor and prevent the influence of moisture, dust as well as sun- and other head radiation.
Only load the device up to the specified limits. Exceeding those limits may damage the device and can lead to fire or
danger for life.
The device may not be opened by the user. Opening the device exposes you to the danger of electric shock.
The device is free of maintanance for the operator. In the case the device is damaged disconnect it from it's supply and
hand it over to trained service staff.
A damage may be:
•
the power cord is damaged
• the device had contact to moisture
•
the device does not operate after correct installation
•
the case of the device is broken
For electrical connection to the device terminals please note the specified lead types and stripping lengths in the datasheet.
Please note the regulatory requirements for installations in distribution boards.
1
in-tech smart charging on the Internet
More information about our products and about Powerline Communication can be found on our website
www.smartcharging.in-tech.com.
On the product page for your device you can find product description, documentation as well as updated firmware.
If you have further ideas about our products please contact us via E-Mail at smartcharging@in-tech.com.
Function
•
persistant storage of configuration
•
support for multiple standard network protocols
(DNS, DHCP, AutoIP, TCP/IP, HTTP, IGMP, ICMP, IPv4-Multicast, UPnP)
• simple mounting on standard DIN rails
• encrypted communication via powerline (HomePlug AV2)
•
Button for easy encryption setup and resetting the device to factory defaults
Figure 1: Control Elements and Connectors
Installation
Important safety instructions
The following safety instructions must be read carefully and clearly understood prior to the assembly of the device. Please
keep these safety instructions for future reference.
•
The installation and assembly may only be carried out by a qualified electrician.
•
This device, which is supplied with mains power, has to be secured by means of a max. B16A circuit breaker.
• This device is designed for installation on DIN rails which provide fire protection as per DIN EN 60950-1.
•
The device may only be installed in dry areas.
•
Do not insert any objects in the slots and openings on the housing.
• Make sure that the device is not exposed to heat sources which may lead to overheating.
•
Ensure adequate ventilation at the site of installation.
•
The device may only be connected in the range of overvoltage category 2 or lower.
• The device may not be opened by the user. The interior of the housing does not contain any parts to be maintained.
•
Do not operate the device in supply networks which do not comply with the specifications on the type plate.
2