Advertisement
Quick Links
T
H
E
T
T
H
E
T
R
S
-
2
3
2
C
o
n
t
r
R
S
-
2
3
2
C
o
n
t
r
The Compli Blu can be operated by RS-232 control. The RS-232C port is configured as a DCE device
using a female 9-pin D-Sub type connector.
RS-232 Pin Configuration:
The pin out of the Compli Blu unit's RS-232C port is as follows:
Pin
2
3
5
This pin configuration allows a PC running a serial terminal program (such as Hyper Terminal) to
communicate with the player using a straight-through DB9 9-pin RS-232 serial cable. Do NOT use a
"Null-Modem" type cable for PC connection. For connection to a remote control system, please
refer to the documentation that comes with the remote control system.
Communication Settings:
The RS-232 control port of the Theta Digital Compli Blu uses the following communications settings:
Baud Rate: 9600
Data Bits: 8
Parity: None
Stop Bit: 1
Flow Control: None
Command Structure:
Each command starts with a # sign (ASCII 0x23), followed by a 3-character command code. If there
are any parameters for the command, the parameters are given in text format, separated by a space
(ASCII 0x20) from the command code. The # character (ASCII 0x23) must never appear in the
parameters. A carriage return (ASCII 0x0d) indicates the end of the command. Each command must
not exceed 25 bytes including the start of command and end of command bytes.
The illustration of the command structure is as follows:
<Command> = <Start of Command><Command Code>[<sp><Parameters>]
<End of Command>
<Start of Command> = #, ASCII 0x23
<Command Code> = <byte><byte><byte>
<sp> = space, ASCII 0x20
<Parameters> = command-specific
<End of Command> = CR, ASCII 0x0d
A
D
I
G
I
T
A
D
I
G
I
T
o
l
P
r
o
t
o
c
o
l
o
l
P
r
o
t
o
c
o
l
Signal
TXD
RXD
GND
A
L
C
O
M
A
L
C
O
M
P
L
I
B
L
U
P
L
I
B
L
U
Version 1.00
Page 1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Theta Digital COMPLI BLU
Summary of Contents for Theta Digital COMPLI BLU
- Page 1 Page 1 The Compli Blu can be operated by RS-232 control. The RS-232C port is configured as a DCE device using a female 9-pin D-Sub type connector. RS-232 Pin Configuration: The pin out of the Compli Blu unit’s RS-232C port is as follows:...
- Page 2 Page 2 Response Structure: Upon receiving a command, the player shall try to execute the command and send back a response. The response starts with an “@” sign (ASCII 0x23), followed by a result code, either “OK” or “ER”. If there are any parameters or additional message, the parameters or message is given in text format, separated by a space (ASCII 0x20) from the result code.
- Page 3 Page 3 OPEN Open/close the disc tray OK OPEN OK CLOSE Discrete on OK ON Discrete off OK OFF Switch output TV system: OK NTSC NSTC, PAL or MULTI(AUTO) OK PAL OK AUTO DIMMER Dim front panel display OK ON OK DIM OK OFF PURE AUDIO...
- Page 4 Page 4 STOP Stop playback PLAY Start playback PAUSE Pause playback PREV Skip to previous Fast reverse play OK 1 X OK 2 X OK 3 X OK 4 X OK 5 X Fast forward play Same as above NEXT Skip to next AUDIO Change audio language or...
- Page 5 Page 5 OK PLAY OK PAUSE OK STOP OK STEP OK FREV OK FFWD OK SFWD OK SREV OK SETUP OK HOME MENU OK MEDIA CENTER Query Track/Title OK 2/10 Query Chapter OK 3/3 Query Track/Title elapsed time OK 0:1:34 Query Track/Title remaining time OK 1:20:23 Query Chapter elapsed time...
- Page 6 Page 6 Set zoom ratio. OK 1.2 AR – Aspect ratio correction (OK followed by the (Stretch, Letterbox or Pillarbox) original parameter) FS - Full Screen US - Underscan For HDMI Output: 1, AR, FS, US, 1.2, 1.3, 1.5, 2, 1/2; For Component Output: 1, 2, 3, 4, 1/2, 1/3, 1/4) 0 –...
- Page 7 Page 7 @OK PLAY ; You may get “ER OVERTIME” message due to the ; mechanical delay. This is normal #QDT ; Check disc type @OK LOADING ; Player is still loading (Wait for a while) #QDT ; Check disc type again @OK BD-MV : Disc is a Blu-ray disc.
Need help?
Do you have a question about the COMPLI BLU and is the answer not in the manual?
Questions and answers