Advertisement
Quick Links
You must read and understand all of the following instructions
before first use. If you do not, it could result in serious injury up
to and including death. Any questions please call 309-691-9653.
• Make sure you have read and understand all instructions.
• Practice first at ground level.
• Always wear TMA approved fall arrest system when using
any treestand.
• Do not use while intoxicated or when taking medications that
cause drowsiness.
• Do not attach to rotten, loose bark or dead trees, metal or
utility poles.
• Avoid use during wet or icy conditions, or during lightning storms.
• Haul gun or bow up from ground after climbing tree.
• Platform is designed to hold one person only.
• Do not jump on platform or seat, nor should you stand on seat.
• Do not attempt to alter product in any way.
• Maximum load is 350 pounds, except where noted.
• Failure to follow these instructions could cause serious injury or death.
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
WARNING!
WARNING!
visit our web site (www.lonewolfstands.com)
Advertisement
Summary of Contents for Lone Wolf Alpha Hand Climber
- Page 1 WARNING! You must read and understand all of the following instructions before first use. If you do not, it could result in serious injury up to and including death. Any questions please call 309-691-9653. WARNING! • Make sure you have read and understand all instructions. •...
- Page 2 PRODUCT LINE INSTRUCTIONS MANUAL PO Box 62 LONE WOLF PORTABLE TREESTANDS Edwards, IL 61528 Phone: (309) 691-9653 • Fax: (309) 693-9410 www.lonewolfstands.com...
- Page 3 WARNING! You must read and understand all of the following instructions before first use. If you do not, it could result in serious injury up to and including death. Any questions please call 309-691-9653. WARNING! • Make sure you have read and understand all instructions. •...
-
Page 4: General Maintenance
General Maintenance • Make sure all nuts and bolts are secure before each use. • Replace any worn or damaged parts with components from Lone Wolf. • All bolts for this product are Grade 8. POLYURETHANE TRACTION BELT APPLICABLE TO: Alpha Sit &... - Page 5 • Failure to follow these instructions could cause serious injury or death. GENERAL MAINTENANCE • Make sure all nuts and bolts are secure before each use. • Replace any worn or damaged parts with components from Lone Wolf. • All bolts for this product are Grade 8. POLYURETHANE TRACTION BELT •...
- Page 6 Shown is the proper use of the traction belt for the Lone Wolf Climbers (dia 1). The polyurethane belts are designed to be used on the Lone Wolf products only. Always use...
- Page 7 Lone Wolf Climbing Stands continued Cam Tethers Step 1: Run the tether through the hole Step 2: Tie the ends together. in the end of the cam. Step 3: Pull the cord to the end of the slot. ALWAYS WEAR A TMA APPROVED FALL ARREST...
- Page 8 Lone Wolf Climbing Stands continued Stabilizer Strap Installation—Climber Seat ™ ™ Alpha Hand Climber and Alpha Sit and Climb. Step 1: For the HAND CLIMBER TOP Step 2: Pull tight. SECTION take the short end of the sta- bilizer straps and take it over the casting in the front corner of the seat through the sewn loop.
- Page 9 Lone Wolf Climbing Stands continued Stabilizer Strap Installation—Climber Base ™ ™ Applicable to Alpha Hand Climber and Alpha Sit and Climb. Step 1: To install the straps on the Step 2: Run the sewn loop through and STAND BASE thread the long end of the pull tight.
- Page 10 Lone Wolf Climbing Stands continued Lone Wolf Climber PLATFORM Installation Applicable to Alpha ™ Hand Climber and Alpha ™ Sit and Climb. First, install the climber base. Step 1: Loosen the torque knobs and pull the hinge washer inward. Step 2: Then, push the hinge forward Step 3: Re-tighten the knobs.
- Page 11 Lone Wolf Climbing Stands continued Lone Wolf Climber PLATFORM Installation continued ™ ™ Applicable to Alpha Hand Climber and Alpha Sit and Climb. Step 4: Unlatch the cam. Step 5: Pull the belt from the tube. Step 7: Insert the belt back into the Step 6: Place around the tree.
- Page 12 Lone Wolf Climbing Stands continued Lone Wolf Climber TOP SECTION Installation Applicable to Alpha ™ Hand Climber and Alpha ™ Sit and Climb. Step 1A: For the HAND CLIMBER flip Step 1B: For the SIT AND CLIMB, the tubes over so they rest on the side of loosen the torque knobs.
- Page 13 Lone Wolf Climbing Stands continued Lone Wolf Climber TOP SECTION Installation continued Applicable to Alpha ™ Hand Climber and Alpha ™ Sit and Climb. Step 4: Retighten the knobs. Now, you Step 5: Unlatch the cam and pull the are ready to put your top section onto belt from the tube.
- Page 14 Lone Wolf Climbing Stands continued Lone Wolf Climber TOP SECTION Installation continued Applicable to Alpha ™ Hand Climber and Alpha ™ Sit and Climb. Step 7: Now re-attach your cam firmly. Step 8: Connect your stabilizer straps. WARNING- the stabilizer straps must be...
- Page 15 Lone Wolf Climbing Stands continued Climbing Instructions – Alpha ™ Hand Climber Step 1: Harness to tree. Step 2: Support your weight onto the climbing aid. Step 3: Place your feet under the Step 4: Bend at the knees to hinges and the bar as shown.
- Page 16 Lone Wolf Climbing Stands continued Climbing Instructions – Alpha ™ Hand Climber continued Step 5: Keeping one foot under the Step 5: Keeping one foot under the Step 6: Slide the harness rope up the Step 6: Slide the harness rope up the...
- Page 17 Lone Wolf Climbing Stands continued Climbing Instructions – Alpha ™ Sit & Climb Step 1: Step into center of from. Attach Step 2: Distribute your weight onto harness rope to tree and lift into postion climbing aid. Place feet under hinge and to climb.
- Page 18 Lone Wolf Climbing Stands continued Alpha ™ Hand Climber Back Packing Instructions Step 1: Fold the stand and seat down Step 2: Lay the top section of the Hand flat placing the two bolt heads into the Climber on top of the platform.
- Page 19 Lone Wolf Climbing Stands continued Alpha ™ Hand Climber Back Packing Instructions continued Step 4: Criss cross stab straps. Step 5: This is the proper position for the Hand Climber to be back packed. ALWAYS WEAR A TMA APPROVED FALL ARREST...
- Page 20 Lone Wolf Climbing Stands continued Alpha ™ Sit and Climb Back Packing Instructions Step 1: The traction belts should be Step 2: Fold the top and bottom flat retracted into the tubes as far as possi- and place the top upside down.
- Page 21 Lone Wolf Climbing Stands continued Alpha ™ Sit and Climb Back Packing Instructions continued Step 5: Install the bungee cord and stabilizer straps as shown. Step 7: Criss-cross and connect the Step 8: This is the proper position for stabilizer straps. Pull them tight.
- Page 22 See the latest from Lone Wolf at www.lonewolfstands.com Lone Wolf Quiver and The Wolf Pack™ Quiver Stand Mount Wolf Jaws™ “Combo” Silent Tote™ For written and video instructions please visit www.lonewolfstands.com...