Fysic FD-110 Installation

Transmitter Installation:

Transmitter Installation:
● Stick the Transmitter on the wall or the door with ● Stick the Transmitter on the wall or the door with
FD-110 Installation
double-sided adhesive tape. double-sided adhesive tape.

Battery Installation (Transmitter):

Receiver Installation:

Receiver Installation: Indoor-unit:
Transmitter uses a 3V CR2032 battery (included).
● Plug the Receiver into any socket of AC110~240V power. ● Plug the Receiver into any socket of AC110~240V power.
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw drive
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Outdoor-unit:
Auto-leaning Code Wireless Door Chime

Important Note:

Accessories List:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the
● 1 x Receiver
● 1 x User Manual
battery from Transmitter, then put them in a safe place.
● 1 x 3 volts CR2032 battery for transmitter
● Improperly using a battery may cause it to leak and damage nearby items, and can create th
risk of fire and personal injury. Batteries should not be left in an area where the children can

Technical Specification:

● Frequency: 433.92MHz+100KHz
reach them as they may pose a chocking hazard.
● Modulation Type: ASK
● Recycle used batteries following environmental protection practices.
● Ring Volume:＞85dB(within 0.5m)
● Channel space: 1 million sets of auto-learning codes
● Receiver bandwidth: ±90KHz
● Reception Sensitivity:＞-105dBm
● Transmitter Power:＜10mW
Transmitter Installation:
● Power consumption(Receiver): standby:＜0.3W
● Stick the Transmitter on the wall or the door with
● Power consumption(Transmitter): standby:＜5uA working:＜10mA
● Power Supply(Receiver): AC110-240V
double-sided adhesive tape.
● Power Supply(Transmitter): DC 3V (1x CR2032)
● Operating Range:＞150m (in the open air)
Receiver Installation:
Connecting:
Names for Parts: ● Plug the Receiver into any socket of AC110~240V power.
CODE
MODE
VOL
Instruction Manual
Model No.: QH-861AK
● 1 x Transmitter
● 1 x Double-sided adhesive
3 sec.
1
Auto-leaning Code Wireless Door C
2 2
Accessories List:
● 1 x Receiver
● 1 x User Manual
● 1 x 3 volts CR2032 battery for transmitter
Technical Specification:
● Frequency: 433.92MHz+100KHz
● Modulation Type: ASK
● Ring Volume:＞85dB(within 0.5m)
● Channel space: 1 million sets of auto-learning codes
● Receiver bandwidth: ±90KHz
● Reception Sensitivity:＞-105dBm
● Transmitter Power:＜10mW
● Power consumption(Receiver): standby:＜0.3W
● Power consumption(Transmitter): standby:＜5uA working:＜10mA
● Power Supply(Receiver): AC110-240V
● Power Supply(Transmitter): DC 3V (1x CR2032)
● Operating Range:＞150m (in the open air)
Names for Parts:
2
Press lightly the battery
holder at side
Instruction Manual
CR2032 3V Lithium Battery
Model No.: QH-861AK
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
CODE
MODE
VOL
1
● 1 x Transmitt
● 1 x Double-si