Summary of Contents for crystal fires TESC Series
- Page 1 CRYSTAL FIRES 1 VALENTINES BUILDINGS AINTREE L9 5AY TESC REMOTE CONTROL ADDENDUM INSTRUCTIONS NOT ALL FUNCTIONS SHOWN IN THESE INSTRUCTIONS WILL WORK WITH YOUR APPLIANCE IT ALL DEPENDS ON THE VERSION SUPPLIED WITH YOUR PURCHASE VERSION 1 ; 1...
- Page 2 Quickly start user instructions Fire Control This control is situated on your fire. The drawing shows the main features of the control. The control required 3 AA size alkaline batteries to be inserted under the battery compartment cover. The orientation of these is shown moulded into the battery compartment.
- Page 3 Grasp around the handset to unlock its functions. The green unlock light will illuminate to show when the handset is unlocked and ready to accept commands. (N.B. Keep a grip of handset to keep it unlocked, to continue to operate the command buttons.) Mode –...
- Page 4 Operating instruction (Detailed) Upon successful insertion of the batteries in the Handset the display will be as shown. The handset will be supplied paired to the fire and all that is required is to set the time of day and select if a 24h hour clock or 12 hour clock display is required and if temperature display is on Celsius or Fahrenheit.
- Page 5 Setting the Hour Press and release the + or – button to change the hour to the correct hour and press set to store and to move to setting the minute. Repeat this for setting the minutes. Setting the temperature display to Celsius or Fahrenheit. Press and release the + or - button to toggle between C and F .
- Page 6 Advanced settings Menu In the event that you may want to change the other preset settings of the control features. Do not do a long press and hold above but a normal short press and release will take you into the advanced settings area. Advanced settings options are:- •...
- Page 7 The default time period for the snooze time period is 1:00 hour. Pressing the set button again will show you the snooze time period remaining. This can be adjusted by pressing the “+” or “-“ buttons. The timer period that can be set is from 1 minute to 4:00 hours.
- Page 8 HANDSET IS PAIRED ORIGINALLY IN THE FACTORY FOLLOW INSTRUCTIONS BELOW ONLY IF HANDSET UNPAIRED OR REPLACED Pairing the Handset to the Fire Control With 2 good quality AA alkaline batteries in the handset in the direction shown inside, if the handset can be paired with a control, it will have the display with the word TESC on the display as shown adjacent.
- Page 9 Handset – without display Buttons Power button – for On/Off of burner Increase burner power Decrease burner power Activity Light – flashes red when starting and stopping burner only. Illuminates when key pad is unlocked SET Button not used for operation AUX Button used for operating an auxiliary device ( sometimes not used depending upon you fire model) ! ...
- Page 10 Pairing a new handset Remove the back panel and insert two AA Alkaline batteries in the direction shown by the symbols moulded into the compartment and replace the cover. Hold the handset with one hand ensuring your hand is wrapped around the back and that your hand is in contact with both sides of the handset.
- Page 11 Burner regulation When the burner is in operation, hold the handset as described above to unlock the keypad and then press and release the + and – buttons to regulate the flame of the burner. Pressing and releasing the button will move the burner one step at a time.
- Page 12 SWITCH PANELl OR BUTTON PANEL (if fitted) Red indication light Press to increase 9lame Press to decrease 9lame Press power button and hold for a second to start 9ire (release when red indication light appears). Press also to stop 9ire Starting the fire Press and hold the power button ! continuously until the red light illuminates next to the ! symbol (this takes typically 1 second). As the red light illuminates release immediately the power button.
- Page 13 Burner regulation When the burner is in operation, press and release the + and – buttons to regulate the flame of the burner. Pressing and releasing the button will move the burner one step at a time. Pressing the button continuously will move the burner rate to the maximum full when pressing + or minimum burner power if pressing -.
Need help?
Do you have a question about the TESC Series and is the answer not in the manual?
Questions and answers