Gilbarco Veeder-Root FlexPay IV Encore 700 S Manual

Gilbarco Veeder-Root FlexPay IV Encore 700 S Manual

Bank note acceptor bna upgrade kit for e-cim

Advertisement

MDE-5287B
April 2017
700 S Bank Note 
FlexPay
IV Encore
®
Acceptor (BNA) Upgrade Kit for E-CIM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Veeder-Root FlexPay IV Encore 700 S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Gilbarco Veeder-Root FlexPay IV Encore 700 S

  • Page 1 MDE-5287B April 2017 700 S Bank Note  FlexPay IV Encore ™ ® Acceptor (BNA) Upgrade Kit for E-CIM ™...
  • Page 2 This page is intentionally left blank.
  • Page 3: Table Of Contents

    Table of Contents PAGES 1-2 SECTION 1 - INTRODUCTION Purpose............... . . 1 Intended Users .
  • Page 4 This page is intentionally left blank. MDE-5287B...
  • Page 5: Section 1 - Introduction Pages

    Purpose This manual provides instructions to install a Bank Note Acceptor (BNA) Kit on Encore® 700 S E-CIM™. Intended Users This manual is intended for Gilbarco®-trained and certified Authorized Service Contractors (ASCs). Required Tools • Phillips® Screwdriver • 8-mm Socket (Nut Driver or Socket Set) •...
  • Page 6 SECTION 1 - INTRODUCTION This page is intentionally left blank. MDE-5287B...
  • Page 7: Section 2 - Important Safety Information Pages

    Replacement Parts procedures should install, inspect, maintain or service this Use only genuine Gilbarco replacement parts and retrofit kits on equipment. your pump/dispenser. Using parts other than genuine Gilbarco replacement parts could create a safety hazard and violate local Emergency Total Electrical Shut-Off regulations.
  • Page 8 SECTION 2 - IMPORTANT SAFETY INFORMATION In an Emergency No Open Fire Inform Emergency Personnel Compile the following information and inform emergency personnel: Open flames from matches, lighters, welding torches or • Location of accident (for example, address, front/back of other sources can ignite fuels and their vapors.
  • Page 9: Section 3 - Removing Components Pages

    SECTION 3 - REMOVING COMPONENTS Before You Begin CAUTION A properly grounded Electrostatic Discharge (ESD) wrist strap must be worn while servicing any electronic devices or components. Failure to use electrostatic precautions may damage electronic components and void warranty. To prepare the site and unit for the installation: Perform an inventory of the parts list provided.
  • Page 10: Lower Hydraulic Panel

    SECTION 3 - REMOVING COMPONENTS Lower Hydraulic Panel Remove the lower hydraulic panel. Note: Place the lower panel safely to the side. Figure 1: Removing Lower Hydraulic Panel Main Door Lower Hydraulic Panel Open the main door. MDE-5287B...
  • Page 11: Cables And Electronics

    SECTION 3 - REMOVING COMPONENTS Cables and Electronics Note: Work on one side at a time to ensure that the components do not get swapped from door to door. Disconnect all cabling from the main door. Remove all the electronics [money/volume display, totalizers, Price Per Unit (PPUs), etc.] from the main door.
  • Page 12: Main Door

    SECTION 3 - REMOVING COMPONENTS Main Door To remove the main door: Open both the doors. Push the CD top cover to the other side to expose the top hinge. Remove the main door prop rod. Note: Retain the main door prop rod for reinstallation. Pull the top hinge pin out and remove the main door from the dispenser.
  • Page 13: Section 4 - Installation Pages

    SECTION 4 - INSTALLATION BNA Bracket To install the BNA bracket: Position the BNA Bracket (M07923A001) on the T-rail and the U-channel in the electronics cabinet  [to the left of the printer (see Figure 1)]. Mount the BNA bracket using the four Button Cap Head Tamperproof Socket Screws (M07335B007). Figure 1: Mounting BNA Bracket T-rail Positioning BNA Bracket...
  • Page 14: Bna Assembly

    SECTION 4 - INSTALLATION BNA Assembly To install the BNA assembly: Locate and unpack the BNA Assembly (M08074A003). Open the top access door and remove the money cassette. Figure 2: Installing BNA Assembly Top Access Door Money Cassette MDE-5287B...
  • Page 15 SECTION 4 - INSTALLATION Position the BNA assembly (see Figure 3) to the BNA mounting bracket, aligning the two holes with the two studs. Mount at the rear side of the BNA using two Q12885-06 Nuts. Mount at the lower side using a M00417B101 Screw. Figure 3: Positioning BNA Assembly Positioning BNA Assembly Q12885-06 Nuts...
  • Page 16 SECTION 4 - INSTALLATION Figure 5: Vault Detail Diagram Vault Opens from Top for Money Cassette Access Cash Cassette Hasp for Lock Vault Switch Engagement Section P192 Connector to Vault Switch Vault Switch Yellow Cash Cassette Release Main Door Slide Door-open Switch Connection Point ...
  • Page 17: Main Door

    SECTION 4 - INSTALLATION Close the lid to the BNA vault. Figure 6: Closing Lid to BNA Vault Lid to BNA Vault Main Door To install the main door: Mount the main door to the dispenser. Insert the main door lower hinge pin into the lower hinge bracket. Figure 7: Inserting Main Door Lower Hinge Pin Main Door Lower Hinge Pin...
  • Page 18: Main Door Electronics

    SECTION 4 - INSTALLATION Insert the upper hinge pin. Figure 8: Inserting Upper Hinge Pin Upper Hinge Pin Reinstall the main door prop rod. Main Door Electronics Reinstall the main door electronics, and then reconnect all cabling. Figure 9: Reinstalling Main Door Electronics and Reconnecting Cables Main Door Electronics Reconnect Cables Repeat steps in...
  • Page 19: Completing Installation

    SECTION 4 - INSTALLATION Completing Installation To complete the installation: Inspect all the connections and cable routing before applying power. IMPORTANT INFORMATION Cable routing is critical. It is very important to route and dress the cables properly. Exercise care in routing the cables, keeping in mind that the door(s) open and close for service.
  • Page 20 SECTION 4 - INSTALLATION This page is intentionally left blank. MDE-5287B...
  • Page 21: Section 5 - Reference Information Pages

    SECTION 5 - REFERENCE INFORMATION Related Documents Document Title MDE-3804 Encore and Eclipse Start-up/Service Manual ® MDE-4366 USB Printer Maintenance Guide MDE-4609 Heater/Fan Kit (M07333K00X) Installation Guide for Encore 300/The Advantage Series [with FlexPay ® (Canada Only)] and Encore S/Encore 500 Units ®...
  • Page 22 SECTION 5 - REFERENCE INFORMATION This page is intentionally left blank. MDE-5287B...
  • Page 23: Section 6 - Appendix Pages

    SECTION 6 - APPENDIX Wiring Diagrams Figure 1: Flexpay IV BNA Wiring Diagram M03184A005 BNA TX LED BNA RX LED AC Wiring (black, white, green) Through side of Vault To side of BNA AC Wiring (black, white, green) (Part of AC Wiring Harness, M04406A001) Figure 2: Main Door Switch Cable Diagram P192...
  • Page 24 The Advantage® Series, CRIND®, Eclipse®, Encore®, and Gilbarco® are registered trademarks of Gilbarco Inc. E-CIM™ and FlexPay™ are trademarks of Gilbarco Inc. EMV® is a registered trademark of EMVCo LLC. Europay® and MasterCard® are registered trademarks of MasterCard International Inc.

Table of Contents