Summary of Contents for MITECH MICRO 8
- Page 1 MICRO 8 MINIATURIZED DIGITAL MICROWAVE BARRIER 200 m RANGE WITH PLANAR ANTENNA Installation and user manual MADE IN ITALY...
-
Page 2: Table Of Contents
Description of columns and parameters modification Columns READ - WRITE - REAL TIME Connection options via RS485-USB adapter Warnings Page 20 Product photos Page 21 Notes Pages from 22 to 23 MICRO 8 Installation and user manual Page 2 of 24... -
Page 3: Introduction And Warnings
MICRO 8 is the state of the art miniaturized microwave barrier and represents an absolute innovation on the market. Micro 8 has a diameter of only 8 cm and a very narrow lobe aperture. The microwave device has a high degree of reliability and consists of a transmitting and a receiving unit. -
Page 4: Components
(ALSO USABLE WITH MICRO BOX AND MICRO PL ACCESSORIES) CABLE GLAND MICRO PL MICRO BOX POLE MOUNTING BOX FOR WALL OR POLE TO USE BRACKET MOUNTING WITH MICRO BOX (Dimensions 100x100x50 mm) MICRO 8 Page 4 of 24 Installation and user manual... -
Page 5: Wall Installation
7. Insert the following components (figure 5): - polycarbonate cover - closing cap by tightening it with the M4 screw - Screw cover cap Figure 5 Figure 4 Figure 1 Figure 2 Figure 3 MICRO 8 Page 5 of 24 Installation and user manual... -
Page 6: Wall Installation With Micro Box
5. Follow the procedure already indicated in the pole installation from point 3 (see page 5). Figure 2 Figure 3 Figure 4 Figure 1 Figure 5 Figure 6 Figure 7 MICRO 8 Page 6 of 24 Installation and user manual... -
Page 7: Pole Installation
7. Insert the following components (figure 5): - polycarbonate cover - closing cap by tightening it with the M4 screw - Screw cover cap Figure 1 Figure 2 Figure 4 Figure 5 Figure 3 MICRO 8 Page 7 of 24 Installation and user manual... -
Page 8: Pole Installation With Micro Box
5. Follow the procedure already indicated in the pole installation from point 3 (see page 7). Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 MICRO 8 Page 8 of 24 Installation and user manual... -
Page 9: Mounting Options Pages From 5 To
It is possible to orient the antenna vertically by adjusting the four fixing screws up to a maximum of 5 °. FRONT VIEW SIDE VIEW 1 LATERAL VIEW 2 LATERAL VIEW 3 5° DOWNWARD 5° UPWARD ADJUSTMENT ADJUSTMENT MICRO 8 Page 9 of 24 Installation and user manual... -
Page 10: Introduction
From 80 to 90 cm from the ground Standard compliance EN 50131-1 and CEI 79-3 ROhs compliance 2011/65/UE Protection class IP 65 Warranty 3 years Non-detection zones 1,0 m 2,0 m 3,0 m MICRO 8 Page 10 of 24 Installation and user manual... -
Page 11: Receiver Board (Rx )
LED: led activation Terminal board description: TAMPER IN: tamper input TAMPER OUT: tamper output 0 A B: RS485 ALARM: alarm output WARN: anti-masking output GND: 0 V VIN: +12 Vdc MICRO 8 Page 11 of 24 Installation and user manual... -
Page 12: Transmitter Board (Tx)
LED: led activation Terminal board description: TAMPER IN: tamper input TAMPER OUT: tamper output 0 A B: RS485 ALARM: fault output WARN: not used GND: 0 V VIN: +12 Vdc MICRO 8 Page 12 of 24 Installation and user manual... -
Page 13: Installation
Installation Introduction The MITECH antennas can be managed manually via the dip-switches on both the RX and TX modules or by using the MITECH Radar Barrier configuration proprietary program. IMPORTANT: the modules always keep the last saved configuration in memory even in the event of a power failure. - Page 14 IMPORTANT It is only possible to enter the configuration mode once to program the dip-switches. In manual control mode it is not possible to make changes using the software. MICRO 8 Page 14 of 24 Installation and user manual...
-
Page 15: Control Through Software (Rs485)
MIRS485 module - MITECH radar barrier configuration program start The MITECH Radar Barrier Configuration program allows, via the RS485 serial connection, the maximum and simultaneous management of 16 pairs of antennas, using only one COM port. In case it is necessary to manage more than 16 pairs of antennas, more COM ports must be used. -
Page 16: Description Of Columns And Parameters Modification
With the value 0 db the signal is attenuated by 4 dB. To save the modification, click with the mouse on the red cell of the address you are configuring (figure 4). Figure 1 Figure 2 Figure 3 Figure 4 MICRO 8 Page 16 of 24 Installation and user manual... - Page 17 OK (figure 3). To save the modification, click with the mouse on the red cell of the address you are configuring (figure 4). Figure 3 Figure 1 Figure 2 Figure 4 MICRO 8 Page 17 of 24 Installation and user manual...
- Page 18 IMPORTANT: once the display panel is activated, the configuration table is automatically inhibited and parameters can no longer be changed. To reactivate the commands, click on the Pause button. Pause MICRO 8 Page 18 of 24 Installation and user manual...
-
Page 19: Connection Options Via Rs485-Usb Adapter
TERM jumper in the last connected module. IMPORTANT For all connections it is necessary to respect the following connection diagram: A with A - B with B MICRO 8 Page 19 of 24 Installation and user manual... -
Page 20: Microwave Device Pages From 10 To
5. Supply the device with a stabilized voltage of 13.8 Vdc. 6. Installation must be carried out by qualified personnel. 7. MITECH is not responsible for damages and / or malfunctions of the barriers caused by incorrect installation and / or improper use of the same. - Page 21 Product photos Ø 8 cm MICRO 8 Page 21 of 24 Installation and user manual...
- Page 22 Notes MICRO 8 Page 22 of 24 Installation and user manual...
- Page 23 MICRO 8 Page 23 of 24 Installation and user manual...
- Page 24 Via Ramazzone, 23 Fax: +39 02.48025620 20146 Milano – Italia 43010 Fontevivo (PR) – Italia tech@mitech-security.com www.mitech-security.com MICRO 8 - Rev. 03 – 09/2019 - MITECH® srl reserves the right to change the information in this document without warning. MADE IN ITALY...
Need help?
Do you have a question about the MICRO 8 and is the answer not in the manual?
Questions and answers