1. Manuals
  2. Brands
  3. SES Manuals
  4. Intercom System
  5. SAT2
  6. User and installer manual

SES SAT2 User And Installer Manual

Select entry system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2
SAT
SELECT ENTRY SYSTEMS
User / Installer Guide
SAT2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SAT2 and is the answer not in the manual?

Questions and answers

Summary of Contents for SES SAT2

  • Page 1 SELECT ENTRY SYSTEMS User / Installer Guide SAT2...
  • Page 2 S elf Identifying A utomatic T elephone © Select Engineered Systems, Inc. 8/98 7991 West 26 Avenue Hialeah, Florida 33016 Phone 305.823.5410• Fax 305.823.5215 www.selectses.com...

  • Page 3: Table Of Contents

    Sat Operation (Continued) How to call from a PABX How to change SAT2 Talk Time C H A P T E R How To Set SAT2 4 Digit ID number INSTALLATION How to set SAT2 ID Cycle Time Installation of SAT2...

  • Page 4: Introduction

    After dialing, it permits two way voice communication without having to hold a handset (Hands Free). The amount of time that you can talk on the SAT2 before it disconnects, is programmable from 1 to 99 minutes. The SAT2 can identify itself by sending a 4 digit ID number as a series of Touch-Tones™.

  • Page 5: Sat2 Features, Continued

    Valuable Info If used in Ring Down mode, and the called phone does not answer, or the SAT2 receives a dial tone or busy, will cause the SAT2 to hang up and retry the Be Careful! call. This is programmable from 1 to 9 retries.

  • Page 6: Programming

    Example: To exit program mode, key in 99. I C O N K E Y & Valuable Info If you simply hang up, the SAT2 can not be used for at least one minute. Be Careful! Installers Note User Note SAT2 Feature...

  • Page 7: How To Put In A Single Phone Number

    16 digits long. How To Change SAT2 Talk Time. SAT2 can be set to stay active for conversation from 1 to 99 minutes. The factory default talk time is 1 minute. It beeps 3 times, 10 seconds before disconnecting.

  • Page 8: How To Set Sat2 4 Digit Id Number

    Example: To set the SAT ID Cycle Time from the factory default of 0 (ID on Command) to every 20 seconds, key in 43 2 Þ. & ID on Command is when ID Cycle Time is set to 0. To force the SAT2 to send an ID on Command, press the Þ Þ .

  • Page 9: How To Put In Multiple Phone Numbers

    SAT2 Programming Cont. How To Put in Multiple Phone Numbers. SAT2 can hold up to 10 phone numbers in memory. These phone numbers are stored in locations. The locations are numbered 110, 111, 112, etc. all the way to 119.

  • Page 10: How To Change Sat2 Ring Time

    SAT2 Programming Cont. How To Change SAT2 Ring Time. SAT2 can be set to ring from 10 to 90 seconds before it quits trying and hangs up. Ring Time is in 10 second increments. The factory default Ring Time is 40 seconds.

  • Page 11: How To Change Sat2 Ring Detect

    J After getting into program mode, (see Pg. 3) use your Touch-Tone™ phone to key in 32, a digit from 1 to 9, and Þ. Example: To set the SAT2 Ring Detect from the factory default of 3 to 4 rings, key in 32 4 Þ.

  • Page 12: Sat Operation

    Conversation may go on for whatever length of Talk Time was programmed (1 to 99 minutes, see Pg. 4). 10 seconds before SAT2 times out, it will send three beeps to alert both caller and called party that SAT2 is about to disconnect.

  • Page 13: Sat Operation (Continued)

    G U I D E SAT2 OPERATION, Continued After the SAT2 calls, if an acknowledge tone was programmed (See Pg. 7) and is pressed by the called party, the green light marked TALK, will begin flashing once per second. This lets the person using the SAT2 know that the phone call was received and acknowledged.

  • Page 14: Installation

    Using a wire nut connect the ground wire to a 16 gauge wire that is connected to a ground rod or a cold water earth ground. MAKE SURE THE SAT2, AND THE SAT2 BACK BOX MAKE SURE THE SAT2, AND THE SAT2 BACK BOX ARE GROUNDED TO GOOD EARTH GROUND.

  • Page 15: Installation Of Sat2 (Continued)

    $ Re-Install the door and screw the 6 tamper resistant screws back in the front door. $ Press the call button. If the SAT2 has not been programmed, it will give a brief dial tone, and then hang up. If it has been programmed, it will dial the programmed phone number.

  • Page 16: Converting Sat2 To Ring Down Mode

    34, and 1 - 9, and Þ. Example: To set the SAT2 from a phone line unit to a Ring Down unit with 3 attempts, key in 34 3 Þ. To set the SAT2 back to a phone line unit, key in 34 0 Þ.

  • Page 17: Sat2 Mounting Template

    S A T U S E R I N S T A L L E R G U I D E Installation of SAT2 (Continued) SAT2 Mounting Template I C O N K E Y & Valuable Info Be Careful!

  • Page 18: Fcc Requirements

    The SAT2 has been tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference in a residential installation.
  • Page 19 “BETTER TECHNOLOGY MAKES BETTER SYSTEMS” Last Printing Date 08/02 Select Engineered Systems, Inc. 7991 West 26th Ave. Hialeah, FL 33016 Toll Free: 1-800-342-5737 In FL: 305-823-5410 Fax: 305-823-5215 www.selectses.com...

Table of Contents