Advertisement
INSTRUCTION MANUAL
Hull:
Hull Length:
Overall Length:
Motor:
ESC:
Hull Width:
Servo:
Weight:
ABS
28-1/2" (72cm)
32-1/2" (83cm)
3536/1800kV Water-Cooled BL Motor
60A Water-Cooled Brushless
2-channel, 2.4GHz
14.8V 1-4S or 2- 2S 4000mAh 30C LiPo (not included)
8-1/4" (21cm)
40g Waterproof
49.5 oz. (1403g)
Advertisement
Summary of Contents for Race RC Velocity 800 BL
- Page 1 INSTRUCTION MANUAL Hull: Hull Length: 28-1/2” (72cm) Overall Length: 32-1/2” (83cm) 3536/1800kV Water-Cooled BL Motor Motor: 60A Water-Cooled Brushless ESC: 2-channel, 2.4GHz 14.8V 1-4S or 2- 2S 4000mAh 30C LiPo (not included) Hull Width: 8-1/4” (21cm) 40g Waterproof Servo: 49.5 oz. (1403g) Weight:...
-
Page 2: Table Of Contents
Overview The Velocity 800 BL arrives 100% factory-assembled out of the box with a 2-channel, 2.4 GHz radio heavy-duty Table of Contents ............................2 Quick Start Guide ..........................3 ..........................4 ........................4 ........................4 ........................5 Battery Installation ........................6 ................9 Running Hardware Adjustments.......................10 ............................10 tor Care ............................11 When Finished Running ........................11... -
Page 3: Quick Start Guide
Quick Start Guide 9 of this manual. be controlled by another device. Make sure the outside of the boat and inside of the hull are completely dried out before storing your grow and damage the components. Repair any damage or wear to the boat before running it again. - Page 4 Self-Righting Feature To ensure that the self-righting feature works correctly, be sure that the openings at the left front and rear left of the boat are clear of obstructions before each run. When the boat becomes capsized it will take up to 10 seconds for the internal cavity to fill with water which will cause the Velocity to return to right-side up.
-
Page 5: Battery Installation
Battery Installation power. You can use either one 4S 4000 mAh pack or two 2S 4000mAh packs. When using a single 4S pack the supplied jumper plug must be plugged into one of Unlocked the hook and loop fasteners. Locked Unlocked Rotate the hatch lock 90°... - Page 6 Transmitter Operation Servo Reversing Switches Steering Trim Antenna 5:5 / 7:3 Switch ON/OFF Switch Knob Indicator LED Steering Rate Knob Slide the switch UP for ON and DOWN for OFF Steering Rate Knob range in rudder movement. Counter-clockwise will reduce the range of rudder movement. Adjust to suit your driving style and preferences.
- Page 7 Steering Trim Steering Trim To safely operate the Velocity 800BL, the switch trim when the wheel is centered. straight. Binding is the process of programming the receiver WARNING should have already been bound to the boat at the factory, however if the boat is not responding to the bind cable to bind channel slot.
- Page 8 How to Operate Your Vehicle BIND BUTTON • Off Forward seconds. Pull the trigger towards you to make the vehicle go complete. forward. CAUTION pull it the faster the vehicle will go. Release the trigger to stop. Adjust the trim if the motor does not stop when the trigger is released.
- Page 9 • Connect the equipment into an outlet on a connected. • Contact your local retailer. Checking the Radio System and Getting Started into the ESC inside the hull. Before placing the boat in the water, test the Brake End Point: Hold the trigger in the counterclockwise to adjust the full brake end motor.
-
Page 10: Running Hardware Adjustments
Once you carefully place the boat in the water, The trim tabs on the Velocity can be adjusted to modify begin driving slowly as you become familiar the running attitude of the boat. Turn the trim tab adjuster screws clockwise to “push” the bow down into the water if the boat “porpoises”... -
Page 11: Motor Care
Motor Care is being removed. • frequent starts, stops, turns or pushing items in the water can overheat the motor. Other driving also cause excessive heat and damage the motor. up to the drive dog using marine grease. Apply thread lock to the coupling setscrew. possible. - Page 12 NOTICE: When running at full speed in choppy waters, the prop may exit and re-enter the water quickly and repeatedly. This will subject the propeller to some stress which may eventually cause damage to the point it will need to be replaced. CAUTION cause damage to these materials.
-
Page 13: Replacement Parts List
Rudder Push Rod (2); Velocity 800 BL RGRB1270 Stainless Steel Shaft Bracket; Velocity 800 BL RGRB1271 Running Hardware Set; Velocity 800 BL RGRB1272 Prop Shaft w/ Prop; Velocity 800 BL RGRB1273 Teflon Shaft Tubing; Velocity 800 BL RGRB1257 Stainless Steel Propeller (3); SC700BL, Velocity 800 BL... - Page 14 Limited Warranty Warranty Period: Rage R/C warrants that the Velocity 800BL (“Product”) will be free from original factory defects in materials and workmanship upon purchase (“Warranty Period”). than a Rage R/C authorized service center, or (e) Product not purchased from an authorized Rage R/C dealer. OTHER THAN THE EXPRESS WARRANTY ABOVE, RAGE R/C MAKES NO OTHER WARRANTY OR REPRESENTATION, AND THEREFORE DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND SUITABILITY FOR A PARTICULAR...
- Page 15 Operating and Maintenance Notes:...
- Page 16 v1.0 06/2018 001CHS...
Need help?
Do you have a question about the Velocity 800 BL and is the answer not in the manual?
Questions and answers