Advertisement
4. OPERATION
4.1.
FILLING
4.1.1.
Either fill tank (fig.3) with water and detergent or just water and use detergent bottle (fig.8),
4.1.2.
supplied.
Only use recommended detergent. (Sealey Detergent Model No's SCS001 - SCS006)
9
Non-recommended detergents may damage the machine.
4.2.
POWER SUPPLY
4.2.1.
The washer is powered directly from the vehicle's 12V accessory socket.
4.2.2.
Insert the accessory connector plug (fig.1) into the 12V accessory socket in the vehicle.
It is advisable to leave the vehicle engine running whilst using the washer.
9
4.2.3.
Close hose valve (fig.7) and disconnect the plug from the accessory socket when not in use.
4.3.
PRESSURE WASHING
WARNING! Ensure the hose valve is closed before connecting the hose.
‰
4.3.1.
Connect the 8m hose to the outlet hose situated inside the tank via a push on coupling (fig.2).
4.3.2.
To disconnect the hose, pull or push the connector ring in the direction of the arrows (fig.4)
and pull the hose out.
4.3.3.
To connect the spray gun, ensure the hose valve is closed (fig.7), then push the hose
connector onto the gun (fig.5).
4.3.4.
When connected, open the hose valve (fig.6) and the pump will start and build up
initial pressure, then stop, until the trigger is pulled on the spray gun, to release the
pressurised water. Release the trigger to stop the flow of water.
4.3.5.
The spray pattern may be adjusted by rotating the collar (fig 5).
4.3.6.
The unit is fitted with an automatic stop switch that will turn the pump off when the trigger
is released.
4.3.7.
Always close the hose valve (fig.7) before removing tools.
4.4.
DETERGENT DISPENSER
4.4.1.
To attach the detergent bottle, ensure the hose valve is closed (fig.7) and the detergent
bottle switch is set to off (fig.9). Connect the hose onto the detergent bottle (fig.8).
4.4.2.
The detergent bottle (fig.8) can be removed by unscrewing from the nozzle body.
4.4.3.
When filled with appropriate detergent, (Sealey Detergent Model No's SCS001 - SCS006)
screw the bottle in place.
4.4.4.
The detergent flow is started by opening the hose valve (fig.6), then moving the control
lever on the bottle (fig.9) either to the spray setting or the jet setting.
4.4.5.
When the detergent has been exhausted, set control lever on the bottle to the off position,
close the hose valve, remove the bottle, and refill with neat detergent.
4.5.
BRUSH ATTACHMENT
4.5.1.
Screw the brush handle onto the brush (fig.10). Ensure the hose valve is closed.
4.5.2.
Attach the brush by pushing the hose connector onto the brush handle (fig.10).
4.5.3.
Open the hose valve (fig.6) and pull the trigger on the brush, water will flow into the brush head.
5. MAINTENANCE
5.1.
The pump unit does not require any regular maintenance.
5.2.
The 12V connector plug is fitted with an 8A fast blow cartridge fuse. If blown,
replace with identical fuse.
5.3.
Should the nozzle become blocked, close the valve on the hose and disconnect the gun,
the nozzle can be back-flushed with either water or air to dislodge any blockage.
5.4.
When not in use drain the machine, remove hoses and store in a cool yet frostproof
location beyond the reach of children.
fig.6
© Jack Sealey Limited
fig.7
fig.10
fig.8
Original Language Version
fig.1
fig.2
fig.3
fig.4
fig.5
fig.9
PW2512 | Issue 1 12/12/18
Advertisement
