Related Manuals for Range Road RR5055
Summary of Contents for Range Road RR5055
- Page 1 RR5055 Blade Grinder RR5055 Blade Grinder Owner’s Manual Assembly/Set-up Range Road Enterprises Ltd Box 944 Eckville AB T0M 0X0 www.range-road.ca...
- Page 2 RR5055 Blade Grinder ITEM NAME Push Tooth Pin Push Pin Adjustment Screw Push Pin Adjustment Plate Push Arm Left Pressure Wheel Lock Bolt Left Pressure Wheel Adjustment Rod Right Pressure Wheel Pressure Wheel Plate Pressure Wheel Adjustment Seat Left Pressure Wheel...
-
Page 3: Applications And Features
RR5055 Blade Grinder Applications and Features This tool is used for grinding band saw blades, it can also be used for the grinding of double metal band saw blades, and it can grind both the tooth throat and the rear. -
Page 4: Maintenance And Precautions
RR5055 Blade Grinder Note: Before turning on the power, first adjust the lever 16 back a short distance, and then slowly feed it to prevent the saw tooth from being worn out. Maintenance and precautions 1. The saw blade interface must be smoothed before grinding, and there should be no obstacles when the saw blade advances. - Page 5 RR5055 Blade Grinder Ensure you are wearing gloves and eye protection when working with the Band saw blade Open the box Remove all items You will have 4 items The tower for holding the blade upright The grinding stone Some round handles and...
- Page 6 RR5055 Blade Grinder Lift the Sharpener out of the box Open the bag with the handles and hardware Find the small, round, silver handle and attach it to the shaft located just below the grinding stone electric motor Lock the handle onto the...
- Page 7 RR5055 Blade Grinder Un-package the grinding stone Install onto motor shaft with blue label facing outward Tighten up the lock nut There are two small bolts that are installed near one of the corners loosen and remove these bolts Un-package the tower...
- Page 8 RR5055 Blade Grinder Take the band saw blade to be sharpened, and set machine shown in the photo Take special notice as to what direction the teeth are facing If you set the blade on the machine and find the...
- Page 9 RR5055 Blade Grinder Now that the blade is sitting correct position, lock it into place Loosen the small black cap shown in the photo Adjust Band Saw guide so that it is snug against the back of the blade Tighten the black cap to...
- Page 10 RR5055 Blade Grinder Now that both guides are locked into place, set the press plate onto the blade Install compressor handle and compressor support on top of press plate Do not tighten wing-nut shown in picture yet Leave this loose for now...
- Page 11 RR5055 Blade Grinder Slide the left pressure wheel over the center of the blade Lock into position by tightening wing-nut Slide the Right pressure wheel over the center of the blade In the photo shown, the angle between the pressure roller arm and blade is about 90°...
- Page 12 RR5055 Blade Grinder The blade is now set in the machine The next steps involve getting the blade lined up with the grinding stone to do the appropriate grind on the tooth Now, locate this panel on the side of the machine...
- Page 13 RR5055 Blade Grinder The other, orange switch will still be in the “off” position at this time - the grinder is not spinning at this time Return to the round, black handle(16), and start turning clockwise You will see that the upper...
- Page 14 RR5055 Blade Grinder The next adjustment is the upper table position This adjustment changes the angle of the blade as it contacts the grinding wheel This adjustment is achieved by gripping the left pressure roller and the right pressure roller-...
- Page 15 RR5055 Blade Grinder Switch the table back on, the upper table should be moving back and forth and the blade should be coming very close to the grinding stone with the appropriate angle Turn the grinding motor switch on The table should be moving...