Inter Laser Rabbit HX-1630 Manual

Laser machine with auto feeding fabric from a roll

Hide thumbs

page of 50

/ 50
Bookmarks

Quick Links

Download this manual

Laser machine Rabbit HX-1630

(with auto feeding fabric from a roll)

WWW.INTERLASER.RU

Need help?

Do you have a question about the Rabbit HX-1630 and is the answer not in the manual?

Questions and answers

Summary of Contents for Inter Laser Rabbit HX-1630

Page 1 Laser machine Rabbit HX-1630 (with auto feeding fabric from a roll) WWW.INTERLASER.RU...
Page 2 Safety requirements: Laser improper use can lead to personal injury, so please carefully before using laser the safe use of knowledge, in order to avoid personal injury, and to prevent the product or damage in connection with any of the other products. In order to avoid the possibility of danger, this product only can be used within the prescribed scope.
Page 3 Catalogue Chapter 1 Outlines 1.1 laser development prospect and application range: ……………………………..…..1 1.2 the advantages of laser processing technology ……..……………………………..…….2 1.3 product introduction……………………………………………………………………………………..3 1.4 the main technical indicators……………………………………..……………………………..….3 The chapter 2, t he structure of the laser cutting machine………………………… …. 2.1 structure description ..........................
Page 4 Chapter 1 Outlines 1.1 Machine parameters Rabbit HX-1630 auto-feeding system Model 1600mm×3000mm Working area Cutting Speed 0—60m/min Laser power control 0-100% Laser power 100w Cooling system Water cooling Mechanical resolution 0.025mm Smallest Character Engraving Chinese 2mm, English 1mm <=±0.01mm Locating Precision...
Page 5 Chapter 2 Machine Configurations 2.1 Structure describing Complete working system by laser cutting, laser power, laser cutting host software, exhaust fan, air compressor, water cooling machine, air ducts, computer, communication cable, etc. According to the work object configuration of equipment have printers, scanners, and all kinds of design software and so on.
Page 6 (1) Auto-feeding system with Nets worktable( stainless steel) Groove on the shaft rubber can effectively prevent the platform in the process of feeding cheap, thus increasing the accuracy of the feed Pneumatic pressure cloth feeding device, when a version (3 m) length of fabric cutting, cylinder automatically down then...
Page 7 receiving box and then move the next version of the cutting cylinder rises, the whole process fully automated, do not need artificial auxiliary. Pneumatic pressure cloth feeding the benefits of migration is to prevent the process of feeding material and improve the accuracy of continuous cutting feed.
Page 8 After one version cutting, the materials are all sent to the receiving box, machine cutting and people collecting at the same time, very convenient one people operate is ok. (2) Control panel and USB connection Easy to operate, USB offline control system: design on one computer and used on many machines, saving the PC memory source.
Page 9 Control system Schematic diagram (photo for reference, pls in kind prevail) WWW.INTERLASER.RU...
Page 10  Terminal  Servo motor  Signal of laser power supply socket  Control card (powercut)  Filter  6 - X axis motor driver  Light  Protection switch  DC48V Supply for steeper motor  DC24Vsupply for control card ...
Page 11 Chaper 3 machine installation 3.1 Remove the packing On the packing first to check whether there is any damage on the laser tube, and then check whether there is any scratch on the machine appearance and accessories are complete. If there is any damage on the packaging or before open the machine during the installation process have any damage, please inform us of the company or authorized agent.
Page 12 3.3 Supply connection Schematic diagram:  input supply Connect with 220V output supply for air compressor output supply for water chiller air output air input water input 3.4 laser tube structure  CO2 sealing Laser tube  Laser tube structure: Laser tube is the most critical components in laser machine.
Page 13 Length of coarse, tube short fine point. Discharge tube length is proportional to the output power. Within the scope of a certain length, discharge tube per meter length of the output power increases with the total length. Discharge tube in both ends connect to store the trachea, trachea has a small hole at the end of the storage and discharge tube, the other end through the spiral muffler and discharge tube are interlinked, so it can make the gas in the discharge tube and store circulating in the trachea, the gas discharge tube exchange at any time.
Page 14 3.5 Laser supply installation The power supply cord on the laser tube installation Distinguish correctly the laser tube is negative, generally is the laser output is negative (-), the other end to the positive (+). 1 - water inlet 2- laser tube anode 3- laser tube cathode 4- water outlet WWW.INTERLASER.RU...
Page 15 3.6 Water chiller installation: Outlet and inlet of water cooling machine on rubber hose. Open the machine power supply, water cooling machine start working, loop observation of laser tube have blisters after 1 minute, if you have blisters slightly rotating laser tube to squeeze blisters. Note: the laser tube inlet side down, outlet up, so that the laser tube there would be no blisters.
Page 16 （） Water chiller higher than 80w laser power match water chiller 1- water inlet connect with machine outlet 2- water outlet connect with machine inlet 3- water protection line 4- water chiller supply 5- аlarm light 6- temperture display screen 7- working Light 8-supply switch WWW.INTERLASER.RU...
Page 17 water-cooled machine cooling water requirements: cooling water with pure water, had better be highly purified water, and often pay attention to the water temperature of cooling water, ℃ ℃ water temperature should be controlled in the range of 15 to 30 , may not be too high or too low, especially in the summer, once found, high temperature cooling water should be replaced in a timely manner or stop to rest for a period of time.
Page 18 3.6 air compressor and air pump installation Applicable materials: wood, plywood, MDF, die board, paper, leather flammable materials cutting 1-display table 2 air output control switch 3- air compressor supply line 4- air compressor 5- air outlet 6- air filter 7- air filter outlet 8- oil filter equipment 9- air pressure adjust device...
Page 19  3.7 the installation of exhaust fan The air inlet of fan with white tube and machine exhaust port connection, plug in the power cord of the fan. Fan for a long time use, can make the fan inside the accumulation of a lot of solid dust, let the fan make a big noise, in addition to flavor and is unfavorable to the exhaust.
Page 20 3.9 Control software installation ： Hardware requirements > 2.1G Internal storage >256M Hard disk >20G Software requirements: （、） Microsoft Windows operation system Window2000 WinXP Software installation is very simple, users only need to put the CD the software copy directly to the hard ，...
Page 21 1. laser frame structure diagram (2) for adjusting screw up and down, can only be fine-tuning. When the screw tightening laser downwards migration (3) for retaining screw (4) adjusting screw for the upper left or lower right, when the screw to tighten the laser into the upper left corner (5) for adjusting screw, when the screw tightening laser right deviation (6) for adjusting screw up and down, up and down to a wide range of adjustment...
Page 22 1- fix the screw 2- adjust the screw 3- airway tube 4- lens cone 5- For the lock cap, used to adjust the up and down and fixed 6- For the lock cap, inside is focusing mirror 7- For the outlet and laser output 8- air inlet laser path adjust Laser beam from the laser tube first shot at the center of the first mirror area (laser beam effect in the...
Page 23 1) Adjust the first reflecting mirror. With acrylic or other transparent non-metallic materials in the second reflection mirror, adjust the first mirror knob screw, the laser from laser tube to hit the center of the second mirror lenses. 1-laser power output place( first reflective mirror) 2-second reflective mirror 3-third reflective mirror Green line is the laser running road...
Page 24 2) Adjust the second reflective mirror Step 1: before the third mirror with a small piece of the acrylic board or paper can play a tag object, such as laser will be moved to the nearest second reflecting mirror, according to some, a laser spot on Step 2: laser will be moved to the furthest away from the second mirrors to play on a laser spot.
Page 25 5) djust the focus lens Put a piece of the acrylic plate on the worktable, point try to see if by penetrating acrylic around before and after laser vertical. No vertical adjustment screws on the third mirror will light up the vertical, make the strongest so far, the energy of the laser spot thus the laser with the focusing lens to vertical;...
Page 26 4.3 the focal length of how to choose appropriate focus lens (this method is suitable for very professional staff use) Laser materials processing is the direct reasons of the lack of depth and the processing speed: the effective power of the laser processing density is small. For the same material, the effect of laser processing load on processing materials mainly depends on the laser light power density (note: not power), light power density refers to the power per unit area, the calculation formula is:...
Page 27 size for: the shorter the focal length, the smaller is the focus, the shorter the depth of focus also; The longer the focal length, the greater is the focus, with the depth of focus is, the longer focal size and the depth of focus is a pair of contradiction. Depth of focus is refers to the laser focus can be formed after the processing capacity of the length of the laser power concentration areas the longer the depth of focus on processing thick the better, but this will make the focal...
Page 28 Chapter 5 operation panel and instructions （） control panel 5.1 the keys function introduction (File): According to the file into memory under main interface information interface; Long according to the current setting of the file information for file into the interface (U Disk ) (origin) Frame)
Page 29 （） Laser ．。 (Set) （） Enter (Sec) （） Stop (direction) 。 Z axis and X axis change WWW.INTERLASER.RU...
Page 30 5.2 computer connection problems Problem performance phenomenon: 1. read and write parameters, dozen don't start outh; 2. can't read and write parameters; 3. transfer file is nvalid. Solve the steps: 1. check to see if the USB cable connection correct, good. Check whether the USB line interface is connected to the PC.
Page 31 5.5 the profile of laser cutting machine 1- USB connection 2- light switch Red pointer switch WWW.INTERLASER.RU...
Page 32 5.6 the basic operation process machine operation (a) boot 1. Open the water-cooled machine, 3 minutes to let the water cycle in the laser tube. 2. Open the host power supply. 3. Open the fan power 4. Open the laser power supply, with key check whether the light. 5.
Page 33 Close the place around the laser path in case the laser escaped; Try to avoid the same height between the laser head and human eye; Pay attention to the ventilation and exhaust in the laser processing environment; Check the water chiller to see if it can let the water out each time after starting the machine. It is forbidden to start the machine up when water can not come out form the water chiller.
Page 34 In case there is damage or fire, please turn off the power at once. Please do not use the machine when the humidity is more than 80%, or it will affect the life the machine and damage the electronic parts. Don‘t start the machine when there is thunder or lightning.
Page 35  1. Guide rails should be cleaned, and lubricant should be added onto the rail every two weeks. 2. The materials for cleaning the rail: cotton cloth and lubricant oil 3. How to clean the rail : push the laser head to one end of the rail ,and use the cotton cloth clean the rail ,after that ,add some lubricant oil on the different part of the rail ,and then ,push the laser head from one end of the rail to the opposite end, make sure the oil can be symmetrical added on the rail .
Page 36 Ⅶ . Regular failure and failure elimination 7.1. No ray 12. Did not turn on the laser power supply. The laser power switch is on the panel. 13. The laser path is not correct. It could also happen such situation when inclines large. Please refer to the previous section.
Page 37        Pin 1 is H (TH) input signal, which controls the optical switch, when the voltage 3V, the signal will agree the laser tube to send out laser, when the voltage 0.3V, the signal will not agree the laser tube to send out laser.
Page 38 Pin 8 is the negative electrode of the laser power supply Pin 9 is the positive pole of the laser power supply; First, check if any signal from the powercut; when ray continuously, please test the high-level voltage input signal pin 1 and control signal pin 3 by multimeter ( put the positive pole into the high-level voltage input signal pin 1, negative electrode put on the ground wire pin 4), to see the voltage in the multimeter.
Page 39 Pin 1 is 5V VOUT. The maximum current output is 20mA. Pin 2 is H (TH) input signal, which controls the optical switch, when the voltage 3V, the signal will agree the laser tube to send out laser, when the voltage 0.3V, the signal will not agree the laser tube to send out laser.
Page 40 7.3 The engraving surface is not plain Fault phenomenon: there is apparent spine phenomena while cleaning the bottom; when intaglio processing, there is apparent uneven phenomena In the place of rank crossed, when Yang Eagle processing, there is apparent spine horizontal line between the place has character or no character; the deeper clean, the more apparent phenomena.
Page 41 7.4 Spots scattered, not focusing, lens cone heat…phenomena of laser engraving machine. 1. Fault phenomena: the laser beam machining can see yellow, and the rough beam diameter, hollow spot, when the hands touch the focusing tube, has a heat feeling. 2.
Page 42 7.6 Water chiller alarming Firstly, ensure the power supply system normally. Low voltage is easily caused water chiller alarming. So we must make sure the voltage normal, if necessary, chooses the voltage stabilizer. 1) Check the water quantity in the water chiller, less water could cause alarming. Solving method: fill up pure water.
Page 43 7.7 X axis or Y axis does not move around or move abnormally. 1. Control card loosen or stoppage. 2. Limit switch or data line stoppage, check the limit switch, if it has signal, if the line connected well. 3. Drive of equivalent axis stoppage, check the drive supply electricity or not, signals is normal or not. 4.
Page 44 7.9 Different engraving depth or could not engrave deep depth. 1. Check whether the water circulation system is smoothly flowing (water pipes bent or broken); 2. Check whether the focal length is normal, if the focal length is wrong, please adjust the focus. 3.
Page 45 7.11 Wrong size or not closing and malposition when its engraving 1. Edited files is it correct (reset again) 2. Select filed is it out from the size of the layout (choose again) 3. Please check with the parameter of software is it right(set again) 4.
Page 46 7.13 SOFTWARE ERROR ALERT INTERFACE. The operation panel can real-time display the alert interface ,which cause by various improper operation or external disturbance signal. According to the information which display on the panel , it is easy for the user to correct the wrong operation, and exclude the external disturbance signal . 1.
Page 47 Solving method: a) Open the installation catalogue of application procedure, operate version testing procedure, check if the function library match with firmware version, if not match, please contact with the supplier to get a matching function library. b) Double-click application procedure, download configuration. 5.
Page 48 7.14 Normal problems of software 1. When engraving with gradient, double phenomenon This phenomenon occurs when the slope of words carved smaller, usually the reason is "wide" setting slope too large, cause calculation errors, please set "wide" little slope. 2. If you only can move a graphic with one direction, please click ―Shift‖ or ‖Ctrl‖ to recover. 3.
Page 49 6. The X-axis or the Y-axis not move （） Stir knob to chose the DC 5V, test the voltage between PULX or PULY and GND. Take Y axis as example, click the button of ‗up‘ or ‗down‘, the normal voltage is 2.8V, if it is not, we could confirm the controller was broken, please change the controller.
Page 50 Ⅷ . Regulations of repair guarantee We are responsible for the repair of complete machine for one year. Guarantee of laser tube (we are not responsible for blowing out of laser tube caused by high water temperature and frost cracking caused by low water temperature) , mirrors and lens is three months, accessory parts is six months.