Operation; Maintenance And Service - Bosch GLI PortaLED 102 Manual

OBJ_BUCH-1497-005.book Page 11 Wednesday, March 11, 2015 2:14 PM
Battery
Permitted ambient
temperature
– during charging °C
*
– during operation and
during storage °C
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C
**
only for wireless charging batteries
Assembly
Battery Charging (Accessory) (see figure A)
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your cordless worklight.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the cordless worklight is switched off by means of a
protective circuit.
 Do not continue to press the On/Off switch after the
cordless worklight has been automatically switched
off. The battery can be damaged.
To remove the battery 5, press the battery unlocking button 4
and pull the battery upward out of the battery port. Do not ex-
ert any force when doing this.
Observe the notes for disposal.

Operation

Initial Operation
Inserting the battery (see figure A)
Insert the charged battery 5 into the battery port until it can
be felt to engage and is seated flush.
Switching On and Off
To start the cordless worklight, press the On/Off switch 1.
To switch off the cordless worklight, press the On/Off switch
1 again.
Switching on again is not possible until 1 second has elapsed
after switching off.
To save energy, only switch the cordless worklight on when
using it.
Bosch Power Tools
Adjusting the Brightness
Briefly press the On/Off switch 1 to switch on the cordless
worklight with maximum brightness. To adapt any of the
3 brightness steps, press and hold the On/Off switch 1 until
0...+45
the desired brightness is reached.
Temperature Dependent Overload Protection
–20...+50
When exceeding the allowable heat-sink temperature of
GBA 14.4 V ..
60 °C, the cordless worklight switches off. Allow the cordless
GBA 18 V ..
worklight to cool down, then switch the cordless worklight on
GBA 18 V ...W
again.
AL 18..
Working Advice (see figure B–C)
GAL 3680
GAL 18...W**
With the support bracket 6, you can lock the case lid in a 45 °
position. The cordless worklight can also be operated when
the case lid is completely opened or closed.
When the lighting duration is ≤10 minutes, the cordless work-
light flashes 3x and the luminous efficiency is lower.

Maintenance and Service

Maintenance and Cleaning
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
The cordless worklight is maintenance-free and contains no
components that must be replaced or maintained.
To avoid damage, clean the plastic lens of the cordless work-
light only with a dry, soft cloth. Do not use cleaning agents or
solvent.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the cordless worklight.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
English | 11
1 609 92A 184 | (11.3.15)