Advertisement
Quick Links
Advertisement
Summary of Contents for Leap Radial
- Page 1 LEAP TAKING HEALTH SERIOUSLY LEAP Radial Assembly & User Instructions...
- Page 2 Take a stand for Office Wellbeing with LEAP Desks...
-
Page 3: Table Of Contents
Contents LEAP Radial Use/Liability Parts List/Tools Assembly Trouble Shooting Specifications Programming 10-12... -
Page 4: Use/Liability
Assembly Make sure no obstacles are in the desk’s path. WARNING Make sure the desktop is not touching any walls. Pinch Point Make sure all cords are appropriate length to Keep hands and fingers clear. accommodate the change in height. Keep children away from electric height-adjustable desks, control units and handsets. -
Page 5: Parts List/Tools
Parts List Tools Phillips Head Screwdriver Tape Measure 4mm Allen Wrench (included) and/or Power Drill Parts List Part Part Part Side Bracket M6x14 Machine Screw Foot Control Box M6x10 Machine Screw Frame End-CB Handset M5x20 Wood Screw Frame End Power Cord M5x16 Wood Screw Centre Rail Cable... -
Page 6: Assembly
Assembly Lay out all components and hardware to ensure that you have all items listed on the parts page. Slide the Control Box (part 7) off the Frame End-CB (part 3) and set aside. Fully separate Frame End (part 4) from Frame End-CB (part 3). You will find the Centre Rails (part 5) inside. - Page 7 Assembly Slide the two (2) Centre Rails (part 5) into the two Frame Ends (parts 3 & 4) ensuring: a} the slots in the Centre Rail (part 5) face inward b} the slots in the Centre Rail (part 5) are closer to the top edge when the assembly is upside down (see inset).
- Page 8 Assembly Double check that the wood screws are not too long for your desktop and won’t puncture the surface when screwed all the way in. We recommend that you pre-drill any holes needed for fasteners. Never use countersunk screws. Double check that the desk base is properly positioned on the underside of the desktop.
- Page 9 Assembly Turn the assembled desk right-side up. With at least two people, grab the DESK BASE (not the desktop) and turn the desk right-side up. Adjust the pre-installed glides on the Feet (part 2) as needed. Plug the Power Cord (part 9) into a 230v outlet. RESET PROCEDURE Press and hold the DOWN button on the Handset (part 3) until the desk reaches its lowest height.
-
Page 10: Trouble Shooting
Trouble Shooting If your desk is not functioning properly it may need to be reset. Follow the RESET procedure outlined in the USE section. If your desk has a handset with an LED readout and it displays “RST” (reset), perform the reset procedure outlined in the USE section. -
Page 11: Programming
Programming Resetting the base When the LED display shows an error code, press the ‘DOWN’ button for up to 5 seconds until the LED changes to a flashing ‘RST’ Press the ‘DOWN’ button again until the base has lowered and then slightly risen. The base is now ready for use. - Page 12 Programming Setting the LED retracted height Press the ‘DOWN’ button until the base reaches its lowest position. Press the ‘DOWN’ button again until the LED flashes ‘RST’. Press the ‘M’ button until the LED shows the current starting height. Then use the UP/DOWN buttons to revise the starting height. The display will automatically return to a flashing ‘RST’.
- Page 13 Programming The display will automatically return to a flashing ‘RST’. Press the ‘DOWN’ button until the base has lowered a little and then slightly risen. The new setting is displayed. Repeat this process to switch back. *10.3 is centimetres *10.4 is Inches Changing the anti-collision sensitivity Press the ‘DOWN’...
- Page 14 LEAP TAKING HEALTH SERIOUSLY...
Need help?
Do you have a question about the Radial and is the answer not in the manual?
Questions and answers