Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Proma Manuals
  4. Power Tool
  5. FP-20A
  6. Instruction manual

Proma FP-20A Instruction Manual

Bench mill machine
Hide thumbs Also See for FP-20A:

Advertisement

Quick Links

Download this manual
BENCH MILL MACHINE
Instruction manual
Please read this manual thoroughly and follow all directions carefully
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the FP-20A and is the answer not in the manual?

Questions and answers

Related Manuals for Proma FP-20A

Summary of Contents for Proma FP-20A

  • Page 1 BENCH MILL MACHINE Instruction manual Please read this manual thoroughly and follow all directions carefully...

  • Page 2: Important Safety Instruction

    IMPORTANT SAFETY INSTRUCTION READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS TOOL Operator COMMON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO ANY PRODUCT. THESE FACTORS MUST BE SUPPLIED BY THE OPERATOR. PLEASE REMEMBER: 1. When using electric tools, machines or equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury.
  • Page 3 IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE, DO NOT OPERATE THE TOOL! Grounding Instructions This machine has a three-prong plug, the third prong is the ground. Plug this cord only into a three-prong receptacle. Do not attempt to defeat the protection the ground wire provides by cutting off the round prong.
  • Page 4 FEATURE Base Cross feed handwheel Long worktable Fuselage (with protect cover) Drill chuck with arbor Protective dust guard assembly Spindle sleeve locking handle Micro switch assembly Depth display Touch switch panel Electric control box Speed display Emergency stop switch Spindle box cover Fine feeding handle Spindle box Vertical feed handwheel...

  • Page 5: Mounting The Machine

    Installation CAUTION! DO NOT ATTEMPT TO USE THE MACHINE UNTIL INSTALLTION IS CAMPLETED, AND ALL PRELIMINARY CHECKS HAVE BEEN MADE IN ACCORDANCE WITH THIS MANUAL. MOUNTING THE MACHINE The machine should be mounted on a strong, heavy workbench, of sufficient height so that you do not need to bend your back to perform normal operations.
  • Page 6 Operation 1. Before starts to use this machine, operator should go through the instructions carefully so as to acquaint with the construction of the machines, the functions of the various controls and also the driving systems. 2. This machine uses touching button (see operation panel below), operating steps refer to the flow chart.
  • Page 7 same as press the “+” button. 5. Press ‘Stop” button (the red and oval button is “0”), spindle will stop running, if press ‘Start’ button now, spindle runs to the speed last setting automatically. When you operate the mill machine encounter emergency you can press the “Emgency stop switch”...
  • Page 8 Parts drawing ( 1 / MT3 ) --the spindle taper is MT3...
  • Page 9 Parts list ( 1 / MT3 ) --the spindle taper is MT3 Part No. Drawing No. Description Q'ty .1-1 XN3B0206 Spindle box .1-2 GB 818-85 - M4 x 6 Cross recessed small pan head screw H type M4*6 .1-3 X3C0219 Spindle below oil seal ring I .1-4 X20206...
  • Page 10 Parts list ( 1 / MT3 ) --the spindle taper is MT3 Part No. Drawing No. Description Q'ty .1-44 GB 119-86 - A 3 x 10 Round pin A 3*10 .1-45 GB 301-84 - 8106 Thrust ball bearing 8106 .1-46 GB 278-89 - 80106 Deep groove ball bearing 80106 .1-47...
  • Page 11 Parts drawing ( 2 / R8 ) --the spindle taper is R8.
  • Page 12 Parts list ( 2 / R8 ) --the spindle taper is R8. Part No. Drawing No. Description Q'ty .2-1 XN3B0206 spindle box .2-2 X3C02A02 R8 spindle sleeve .2-3 X3C02A01 R8 spindle .2-4 XN3A0215 base plate .2-5 XN3A0204 gaar shaft .2-6 XN3A0210 bevel gear .2-7...
  • Page 13 Part No. Drawing No. Description Q'ty .2-44 GB 278-89 - 80107 deep groove ball bearing 80107 .2-45 GB 893.1 - 62 check ring 62 .2-46 GB 894.1 - 35 check ring 35 .2-47 GB 70-85 - M5 x 16 hexagon socket head cap screw M5*16 .2-48 X3C0206 spindle timing pulley...
  • Page 14 Parts drawing ( 3 )
  • Page 15 Parts list (3) --- note: The no. With “*” means the part showing in metric. Part No. Drawing No. Description Q'ty .3-1 XN3A0901 Column .3-2* XN3A0903A Metric rise and down leadscrew .3-3* XN3A0908A Metric rise and down locking nut .3-4* XN3A0907A Metric rise and down leadscrew nut .3-5...
  • Page 16 Parts drawing( 4 )
  • Page 17 Parts list (4) --- note: The no. With “*” means the part showing in metric. Part No. Drawing No. Description Q'ty .4-1 X31136 The left bracket cover .4-2 XN3A1106 Left cover .4-3 X31131 Longitudinal leadscrew rod bracket left sleeve .4-4 XN3A1102 Work table .4-5*...
  • Page 18 Parts drawing( 5 )
  • Page 19 Parts list (5) (Note: some type without the protective guard assembled) Part No. Drawing No. Description Q'ty .5-1 XN3A2305 Splash guard I .5-2 XN3A2304 Splash guard II .5-3 X20002 Filler strip .5-4 GB 818-85 - M4*6 Cross recessed counter head screws M5*6 .5-5 X20003 Dust guard...
  • Page 20 Parts drawing( 6 )
  • Page 21 Parts List( 6 ) Part No. Drawing No. Description Q'ty .6-1 HY57B Emergency stop .6-2 GB 845-85 - ST2.9 x 6.5 Tapping screw .6-3 Touch panel .6-4 XN3B2511 label .6-5 GB 846-85 - ST2.9 x 9.5 Tapping screw .6-6 XN3B1802 Electric box cover .6-7 Rotate speed display...
  • Page 22 Packing List Name Description Q'ty Remarks Bench Mill type: X2.7 or SX2.7 1 set Fuse 110V/20A or 230V/10A 1 pce. Manual manual 1 pce. S1*S2: 8*10、14*17、17*19 Double end wrench each 1 S: 3、4、5、6、8 L hex wrench each 1 U wrench assembly X3C004 1 pce.
  • Page 23 Circuit drawing (only for 230V) according to your choice...