Table of Contents
Advertisement
Quick Links
TECHNICAL DOCUMENTATION
ReRead all instructions carefully before using the
device and familiarize yourself with all control ele-
ments. If in doubt, contact the manufacturer.
Keep the instructions in a safe place that allows
you to obtain the necessary information at any
time.
REMET CNC TECHNOLOGY
Spółka z ograniczoną odpowiedzialnością
36-053 Kamień, Łowisko 320A
NIP 5170374653
Instrukcja oryginalna
USER MANUAL
WARRANTY CARD
SPARE PARTS CATALOG
PROFESSIONAL chipper
For PTO drive
RT-690R, RT-720R
with hydraulic feed rollers:
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for REMET CNC RT-690R
- Page 1 USER MANUAL WARRANTY CARD SPARE PARTS CATALOG PROFESSIONAL chipper For PTO drive RT-690R, RT-720R with hydraulic feed rollers: ReRead all instructions carefully before using the device and familiarize yourself with all control ele- ments. If in doubt, contact the manufacturer.
-
Page 2: Table Of Contents
REMET CNC TECHNOLOGY SP. Z O.O. Table of Contents GENERAL SCHEME ........................... 3 PURPOSE AND GENERAL DESCRIPTION OF THE APLIANCE ............. 4 SPECIFICATION OF THE DEVICE ....................... 5 SAFETY INSTRUCTIONS ........................6 Personal protective equipment and pictograms ................7 Aggregated with a tractor ....................... 9 CONTROL OF WORK AND SAFETY ZONE .................. -
Page 3: General Scheme
REMET CNC TECHNOLOGY SP. Z O.O. 1. GENERAL SCHEME Page 3 of 28 Producer of machinery and equipment, machining... -
Page 4: Purpose And General Description Of The Apliance
REMET CNC TECHNOLOGY SP. Z O.O. 2. PURPOSE AND GENERAL DESCRIPTION OF THE APLIANCE The device is designed for crushing woody and fibrous garden waste such as tree trunks and branches. ATTENTION This symbol is used in this manual if there is a danger to the user or unauthorized persons. -
Page 5: Specification Of The Device
REMET CNC TECHNOLOGY SP. Z O.O. 3. SPECIFICATION OF THE DEVICE Technical parameters: RT-690R RT-720R MINIMUM/RECOMMENDED POWER 35/60* 55/80* [HP] RECOMMENDED SHAFT SPEED 540-1000 540-1000 PTO[rpm](clock ways) DIAMETER OF CUTTING DISC [mm] WEIGHT OF CUTTING DISC [kg] NUMBER OF KNIVES... -
Page 6: Safety Instructions
REMET CNC TECHNOLOGY SP. Z O.O. 4. SAFETY INSTRUCTIONS GENERAL THOUGHTS The chipper must not be used by: • Persons who are entitled,are not trained ora re under the influence of alcohol or narcotic drugs and psychotropic substances(drugs) and drugs which impair the reaction capability •... -
Page 7: Personal Protective Equipment And Pictograms
REMET CNC TECHNOLOGY SP. Z O.O. Personal protective equipment and pictograms When working with the wood chipper, use it: • glasses / face mask • hearing protectors • protective gloves • protective footwear • protective clothing, close fitting to the body, without loose, sticking straps or sleeves. - Page 8 REMET CNC TECHNOLOGY SP. Z O.O. Warning! Rotating parts, danger of being caught. Safety signs: 1. Keep safety signs in a clean and legible condition. 2. Immediately replace any safety signs that are missing or illegible. 3. For the replaced parts that have a safety mark / sign, also use the current mark.
-
Page 9: Aggregated With A Tractor
REMET CNC TECHNOLOGY SP. Z O.O. Aggregated with a tractor Observe the recommended minimum front load of the tractor in order to maintain stability. Należy Be especially careful when coupling the shredder with the tractor and during its disconnection. Every time before starting work, all the safety switches and the hydraulic system must be checked for correct operation. -
Page 10: Control Of Work And Safety Zone
REMET CNC TECHNOLOGY SP. Z O.O. 5. CONTROL OF WORK AND SAFETY ZONE WORK- MATERIAL INTAKE STOP - EMERGENCY STOP Page 10 of 28 Producer of machinery and equipment, machining... -
Page 11: Removing Material
REMET CNC TECHNOLOGY SP. Z O.O. REMOVING MATERIAL RETURN TO INTAKE THE MATERIAL Page 11 of 28 Producer of machinery and equipment, machining... -
Page 12: Safety Zones During Intake Of Material
REMET CNC TECHNOLOGY SP. Z O.O. SAFETY ZONES DURING INTAKE OF MATERIAL A, B - danger zone with impact, collected material, do not enter. C – operator zone when feeding material (operator's work zone). D – operator safety zone feed regulation. -
Page 13: Safety Zones While Withdrawing Material
REMET CNC TECHNOLOGY SP. Z O.O. SAFETY ZONES WHILE WITHDRAWING MATERIAL A, B, C – danger zone with impact, during material withdrawal (no restraint during withdrawal. D – Operator safety zone during material retraction. Page 13 of 28 Producer of machinery and equipment, machining... -
Page 14: Hydraulic System And Feed Control
REMET CNC TECHNOLOGY SP. Z O.O. Hydraulic system and feed control 1. The connected hydraulic system is under high pressure and high tempera- ture. Oil is irritating to the skin and released under high pressure can cause serious injury. Special care should also be taken when searching for a po- ssible leak. -
Page 15: Activities After Finishing Work
REMET CNC TECHNOLOGY SP. Z O.O. Operators performing work with chipper should constantly observe the work area, and immediately stop work in the event of appearance of outsiders or animals in the working area of machines. Before inserting the material to be cut into the inlet hopper, pay attention to whether the material contains foreign elements harder than wood such as: sto- nes, wires, ropes, nails, rivets, chains, etc., which can damage the knives, cutting... -
Page 16: Rules Of Conduct In Emergency Situations Posing Threats To The Life Or Health Of Employees
REMET CNC TECHNOLOGY SP. Z O.O. Periodically checks that all bolts and nuts are tight. Damaged replace. When replacing a damaged chipper knife, always tighten or loosen the knife using protective gloves and following the instructions in section 9. Rules of conduct in emergency situations posing threats to the life or health of employees. -
Page 17: Prohibited Actions
REMET CNC TECHNOLOGY SP. Z O.O. First start: Despite the lack of working restrictions for the first start of the wood chopper, the following checks are recommended: 1. After working 1 hour: • Check tighten of all bolts and hydraulic system connector, Check the condition of the rotor bearings, •... -
Page 18: Notes And First Aid
REMET CNC TECHNOLOGY SP. Z O.O. It is forbidden using the device while the tractor is moving. It is forbidden making any changes or modifications to the device, making changes or modifications results in immediate loss of the warranty. In addition, the manufacturer is not liable for resulting damage to property and personal injury, death of the operator) resulting from changes or modifications to the device. -
Page 19: Adaptation Of The Power Transmission Shaft
REMET CNC TECHNOLOGY SP. Z O.O. ADAPTATION OF THE POWER TRANSMISSION SHAFT Aby To ensure compatibility with a variety of 3-point fastening systems, the power transmission shaft may be too long or too short. Really Imporant is that the transmission of the telescopic shaft through the telescopic shaft takes place freely, but without shortening to limit the working range. -
Page 20: Replacement And Adjustment Of Axles
REMET CNC TECHNOLOGY SP. Z O.O. REPLACEMENT AND ADJUSTMENT OF AXLES Before adjusting the position of knives or replacing them, the device should be disconnected from the power source and placed on a stable, even and not slippery surface. Scheme of adjusting knives: 1. -
Page 25: Maintenance And Cleaning
REMET CNC TECHNOLOGY SP. Z O.O. MAINTENANCE AND CLEANING Safety instructions for maintenance. The device must be disconnected from the power source and placed on a stable, even and non-slippery surface before carrying out maintenance or repairs. Clean the device before and after each use, and check the tightness of the screws that secure the covers. -
Page 26: Solutions For Exemplary Problems
REMET CNC TECHNOLOGY SP. Z O.O. 13. SOLUTIONS FOR EXEMPLARY PROBLEMS Problem Possible cause Solution Knives if necessary to Blunt knives, sharpen or put in place Knives incorrectly moun- according to instructions The device does not draw branches Immersive rollers bloc- Retract the material ked. -
Page 27: Guarantee Card
REMET CNC TECHNOLOGY SP. Z O.O. 14. GUARANTEE CARD Device symbol: ……………………………… Serial number: ……………………………………… Date of production: 202.… Sale date: …………………………………… Signature of the seller: …………….….………..… _______________________ Rubber stamp ZASADY POSTĘPOWANIA GWARANCYJNEGO: 1. This device has a 24 month warranty. In the case of use in companies, commercial use and any other use than private use, a short warranty period applies. -
Page 28: Declaration Of Conformity Ce
DEKLARACJA ZGONOŚCI UE... - Page 29 WWW.MARGUCIAI.LT INFO@MARGUCIAI.LT Nauja technika: +370 685 54521 Naudota technika iš Danijos: +370 656 24532 Lenkiškos technikos atsarginės dalys: +370 615 68799 Skandinaviškos technikos atsarginės dalys: +370 682 51607 Farmtrac atsarginės dalys: +370 626 19138 Chemikalų purkštuvai, patikra: +370 616 55819 Fermų...
Need help?
Do you have a question about the RT-690R and is the answer not in the manual?
Questions and answers