Related Manuals for Pelton & Crane Solaris 2 SSC Series
Summary of Contents for Pelton & Crane Solaris 2 SSC Series
- Page 1 8’ - SSC96-2-R 8’ - SSC96-2-L Solaris 2 Sterilizaton Center Installation Manual ach Rules! Model: SSC 10’ - SSC120-2-R 10’ - SSC120-2-L 12’ - SSC147-2-R 12’ - SSC147-2-L...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Zach Rules! GENERAL INFORMATION ......................................3 PRODUCT IDENTIFICATION ....................................4 PREPARING THE SITE ......................................5 CABINET BASE INSTALLATION....................................8 BACK PANELS TO CABINET INSTALLATION ................................9 TOWER INSTALLATION......................................10 THREE SHELF STERILIZATION TOWER INSTALLATION.............................12 HANGING RAIL INSTALLATION....................................13 UPPER STORAGE INSTALLATION..................................14 ELECTRICAL STRIP INSTALLATION..................................15 GENERAL ROUTING GUIDE.......... -
Page 3: General Information
GENERAL INFORMATION Zach Rules! Definition of Symbols Product Disposal Contact your local authorized dealer for proper The following symbols may be used throughout disposal of the device to ensure compliance with this manual: your local environmental regulations. WARNING: Failure to carefully follow the Interference with Electromedical Devices described procedure may result in damage To guarantee the safety of electromedical devices, it... -
Page 4: Product Identification
PRODUCT IDENTIFICATION 1.013.2466 R00... -
Page 5: Preparing The Site
PREPARING THE SITE Front View Side View Zach Rules! 1.013.2466 R00... - Page 6 PREPARING THE SITE WARNING: Always lift cabinets by bottom edge, being careful to lift with your legs and not your back. Make all required air, water, and drain attachments from the utilities to the incoming WARNING: stub-up connections before the system installation occurs. Doing so prevents damage to the utility lines from heat associated with some plumbing connection methods.
- Page 7 PREPARING THE SITE ELECTRICAL SPECIFICATIONS Depending on the options ordered, the cabinet should be permanently connected to up to 9 individual branch circuits. The GFCI electrical chase located in the receiving /cleaning and prep & pack areas should be permanently connected to 120vac 15amp circuits.
-
Page 8: Cabinet Base Installation
CABINET BASES AND PARTITION INSTALLATION NOTE: These installation instructions describe the procedures with the technician facing the front of the cabinet. WARNING: Be sure the main power is turned Pull off at the installation site. WARNING: Do not lift cabinets by their Zach Rules! countertops. -
Page 9: Back Panels To Cabinet Installation
BACK PANELS TO CABINET INSTALLATION 1. Identify end panel and back panels. Each back panel width should correspond to the width of its lower cabinet section. 2. Place the end panel on the base using the locating pins. Attach back panel “A” to the end panel using the locating pins. -
Page 10: Tower Installation
INSTALLING THE TOWERS 1. Position tower to the side of wrapping station. Align the wrapping station holes with the tower holes. 2. Using the (4) cabinet to cabinet connectors secure wrapping station module to tower. 3. Secure tower to back panel. 1.013.2466 R00... - Page 11 4. Open the storage cabinet to access mounting holes and remove wire baskets. 5. Remove wire baskets from the clean storage tower module by disengaging their hooks from the column in the back. 6. Position clean storage tower to the sterilization tower. Align holes in the steri towers with holes in the clean storage tower.
-
Page 12: Three Shelf Sterilization Tower Installation
THREE SHELF STERILIZATION TOWER INSTALLATION The 3 shelf sterilization tower must be anchored to the wall in 4 places through a stud in 2 places and through the sheetrock in 2 places using the supplied mounting hardware from the kit that is provided with the tower unit. MUST BE ATTACHED TO WOOD WALL STUD IN 2 MUST BE ATTACHED THRU... -
Page 13: Hanging Rail Installation
INSTALLING HANGING RAIL 1. Install hanging rail to back panel using screws provided. 2. Fasten back panels to studs in wall for additional support. Hardware not included. 1.013.2466 R00... -
Page 14: Upper Storage Installation
UPPER STORAGE INSTALLATION 1. Remove upper modules from their packaging. 2. Remove doors and shelves from modules taking care to store doors in a manner in which all can go back in their original posi- tions. The hinges installed are snap-on/off and can easily be re- moved by pulling the tab located at the back end of the hinge base plate. -
Page 15: Electrical Strip Installation
ELECTRICAL STRIP INSTALLATION Stage 1 and Stage 2 are equipped with 2 power strips, one in each area. Follow the instructions below when installing the strips to the partitions. 1. Unscrew the power strip from the electrical chase and remove it. Slide electrical chase inside Stage 1 and Stage 2 into the back panels. -
Page 16: General Routing Guide
GENERAL ROUTING GUIDE 1. Red light - Red light will already be installed in the dirty storage module. Route wiring through the back of the dirty storage module through cutout in the bottom panel and through the chase into the waste area. 2. -
Page 17: Vistapure Tm Installation
VISTAPURE INSTALLATION 1. The VistaPure system comes in 2 boxes: the filtration system and the tank/accessories/manuals etc. 2. Remove the filtration system and mount the VistaPure backer board inside the base cabinet of the wrap station as shown below using 4 wood screws. 3. -
Page 18: Plumbing Schematic
PLUMBING SCHEMATIC Faucets and HVE to be installed into countertop by plumber. WATER OPTIONAL VISTACLEAR SYSTEM UTILITY AREA 1.013.2466 R00... -
Page 19: Light, Electrical, & Pneumatic Door Controls
LIGHT, ELECTRICAL, & PNEUMATIC DOOR CONTROLS 24DC POWER SUPPLY UNDER SINK MODULE PNEUMATIC DOOR SOLENOID 1.013.2466 R00... -
Page 20: Electrical Strips And Sterilizer T Ower Electrical Schematic
ELECTRICAL STRIPS AND STERILIZATION TOWER ELECTRICAL SCHEMATIC 120VAC OR 230VAC RECEPTACLES Each receptacle on the duplex outlet(s) in the sterilization tower must be hard wired to individual 15 amp branch circuits. (A second receptacle will be supplied with the 3 shelf sterilization tower.) Black/white/green wires to be hardwired to individual dedicated circuits. -
Page 21: Final Assembly/Adjustment
FINAL ASSEMBLY/ADJUSTMENT 1. Re-install all doors and drawers to their modules. 2. Adjust doors using manufacturer’s guidlines in the links below. The door is adjusted at the factory so that doors open and close properly. However, an occasional adjustment may be required over a period of usage. 3. - Page 22 ©2017 Pelton & Crane 11727 Fruehauf Drive Charlotte, NC, 28273 - USA P/N 1.013.2466 Rev. 00, 08/07/17 We reserve the right to make any alterations which may be due to any technical improvements Printed in USA...