Advertisement
Quick Links
Section 3: Mounting without Bracket
Refer to the design guideline to ensure that the condition is
met. Complete Steps 1, 2, and 3 of Section 1: UMC
Installation before following the procedure below.
Step 1: Remove ½" fixture
knockout.
Step 2: Using your thumb or
pliers, push and remove the
knockout of the UMC's front
case.
Step 3: Insert the ½" Chase
Nipple through the knockout
hole of the UMC's front case.
Step 4: Insert the sensor into
the UMC case pulling the
cables through the Chase
Nipple. Make sure the lens and
antenna are visible through
the hole in the front.
Step 6: Mount the UMC to
Step 5: Slide to close the
the fixture by tightening the
UMC back cover.
Chase Nipple with the
locknut.
Section 4: Wiring the Cables to the LED Driver
To Enlighted
Sensors
Section 5: Rotating the UMC
After mounting, rotate the UMC to the required direction and
turn the power on.
Copyright © 2016 Enlighted Inc. All rights reserved.
All other brand or product names are trademarks of
their respective companies or organizations.
Technical Support
For questions regarding the installation or operation of
this product, contact Enlighted
Technical Support: support@enlightedinc.com
Company Contact Information
Location: 930 Benecia Ave, Sunnyvale, CA 94085
Phone: +1.650.964.1094
Web: enlightedinc.com
Model: CASE-FS-D22
Page 5
Step 1: Wire the other end of
the sensor cable to the LED
driver's XSR connections.
To
lamps
From Mains
Page 6
Universal Mounting Case
Installation Instructions
Universal Mounting Case
Shipped Components
• Enlighted Universal Mounting Case
• Enlighted Mounting Bracket
• ½ inch Chase Nipple and Locknut
• 2 nos. #8 Anchor Screws (Drywall
mount)
®
• 2 nos. #8 Metal Self-tapping Screws (Fixture mount)
Items you may Need
• 400BAC Wiremold
Conduit
®
• 18" AWG wire
Tools you may Need
• ½" knockout set
• Hand drill
• Wire stripper
• Pliers
• Phillips screwdriver
93-01651-01 Rev01
Page 1
Advertisement
Related Manuals for enlighted Universal Mounting Case
Summary of Contents for enlighted Universal Mounting Case
- Page 1 Step 3: Insert the ½” Chase Nipple through the knockout hole of the UMC’s front case. Universal Mounting Case Copyright © 2016 Enlighted Inc. All rights reserved. Step 4: Insert the sensor into All other brand or product names are trademarks of Shipped Components the UMC case pulling the their respective companies or organizations.
- Page 2 The Universal Mounting Case is designed for use with the two- Step 4: Insert the UMC into Step 3: Slide to open the UMC wire Fixture Mount (FS-D22) sensor. the mounting bracket. Pull back cover. Design Guidelines the sensor cables through...
- Page 3 • this device must accept any interference received, including interference that may cause undesired operation. LED Status Description/Solution Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. LED not on Check power and wiring.
- Page 4 Mounting using the Adjustable Mounting Bracket Caution Step 3: Connect the sensor cable’s RJ12 connector to the Installation and maintenance must be performed by a qualified sensor bottom. The Smart Sensor (SU-4S) can be mounted on pendant electrician in accordance with local, state, and national electrical and industrial fixtures using the mounting bracket.
- Page 5 • this device must accept any interference received, including Technical Support: support@enlightedinc.com interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
- Page 6 Verify that the RJ12 cable is plugged into the Installation flashing LED Control Unit. lights Figure 2: Sensor Distance from the Fixture To install the Enlighted Smart Sensor Unit, perform the following steps: Possible solutions: Red, flashing Replace the RJ12 cable • Step Description •...
- Page 7 Blue solid Sensor received a request to identify itself Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
- Page 8 Unit Step 4: Knock out a ½ inch hole on the end of the light fixture. Step 1: Use an RJ45 coupler with an Enlighted Sensor Step 1: De-energize the luminaire. Step 5: Mount the Ruggedized Sensor LB Conduit to...
- Page 9 • this device must accept any interference received, including Technical Support: support@enlightedinc.com interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
- Page 10 Caution Installation Steps (Continued) Troubleshooting Problem Solution Step Description Installation and maintenance must be performed by a • qualified electrician in accordance with local, state, and LED is not on when 1) Check to see that power is present Install the receptacle in the wall box national electrical codes (NEC) and requirements.
- Page 11 (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's Copyright © 2016 Enlighted Inc. All rights reserved. Model GW-2-01 authority to operate the equipment.
- Page 12 Verify the Cat-6 cable codes (NEC) and requirements. Gateway (GW) is between the PoE port on on or blinking. the Ethernet switch and the Enlighted Gateway Installation Steps (both wall & ceiling mounts) has not been damaged. Step Description •...
- Page 13 • this device must accept any interference received, including Technical Support: support@enlightedinc.com interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
-
Page 14: Figure 1
3/8 inch of exposed wire. Step 6: Insert one end of the pair of wires into the LED XSR driver’s connections wire holes. See Figure 2. Figure 4 To Enlighted sensor lamps Step 9: Close the light fixture and restore power to the fixture. - Page 15 • this device must accept any interference received, including Technical Support: support@enlightedinc.com interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
- Page 16 Position the ERC2 on either the wall or on a junction box with the LEDs on the top and the Enlighted logo on the bottom. (See Figure 5) Use the provided tapping screws (or machine screws for a junction box) to attach the ERC2 to the wall.
- Page 17 Energy Manager radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful Copyright © 2016 Enlighted Inc. All rights reserved. Installation Instructions interference to radio communications. Operation of this equipment All other brand or product names are trademarks of in a residential area is likely to cause harmful interference in which their respective companies or organizations.
- Page 18 Caution Step 4: Use an Ethernet cable to connect LAN2 port on the Step 2: Attach the EM to the Installation and maintenance must be performed by a EM to a standard port on the PoE switch. backer board using the qualified electrician in accordance with local, state, and mounting screws.
- Page 19 Fixture Mount Control Unit commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in Copyright © 2018 Enlighted, Inc. All rights reserved. Model CU-4E accordance with the instruction manual, may cause harmful All other brand or product names are trademarks of interference to radio communications.
- Page 20 Caution Step 11: Install the RJ45 sensor cable between the Control Unit and the Enlighted sensor. Do not use RJ12 cable as it may Installation and maintenance must be performed by a damage the sensor port. Refer to the corresponding Sensor...
- Page 21 If there is no motion in the Changes or modifications not expressly approved by Enlighted Inc. sensor’s field of view, the blinking will stop. Wave could void the user's authority to operate the equipment.
- Page 22 Step 6: Insert the 8-pin end of Step 4: Thread the plain end of the nut from behind the Caution the sensor cable through the tile to secure the carrier. Installation and maintenance must be performed by a qualified carrier. electrician in accordance with local, state, and national electrical codes (NEC) and requirements.
- Page 23 • this device must accept any interference received, including Web: enlightedinc.com interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
-
Page 24: Figure 4
Step 6: Insert the Compact Sensor Caution Step 6: Insert the end of the wire into the sensor’s 6-pin through the hole in the fixture. Use the connector. See Figure 2. Installation and maintenance must be performed by a qualified spring arms from behind the sensor to electrician in accordance with local, state, and national electrical fasten the Compact Sensor. - Page 25 • this device must accept any interference received, including Technical Support: support@enlightedinc.com interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
-
Page 26: Figure 2
Strip each end of the Note: For any reason, if you need to two wires leaving 3/8 inch of exposed wire. remove the two wires, push down on To Enlighted Step 3: Determine the location the tabs located on the rear of the sensor... - Page 27 Company Contact Information Location: 930 Benecia Ave, Sunnyvale, CA 94085 Phone: +1.650.964.1094 Web: enlightedinc.com Copyright © 2015 Enlighted Inc. All rights reserved. All other brand or product names are trademarks of their respective companies or organizations. 93-01218-01 Rev02 Page 1...
- Page 28 Cautionary Suggestions Step 5: Connect the Antennas On Ports 1 and 3 (the outside ports) Disconnect all power before installation or service. • Installation and maintenance must be performed by qualified personnel. • Connect the Ethernet cable Connect the Installations and maintenance must be performed in accordance with •...
Need help?
Do you have a question about the Universal Mounting Case and is the answer not in the manual?
Questions and answers