Related Manuals for Isonas PowerNet IPBridge Series
Summary of Contents for Isonas PowerNet IPBridge Series
- Page 1 How to Install a PowerNet™ IPBridge Copyright © 2013, ISONAS Security Systems All rights reserved...
-
Page 2: Table Of Contents
Table of Contents 1: INTRODUCTION ............................ 4 1.1: BEFORE YOU BEGIN ........................4 1.2: GENERAL REQUIREMENTS: ...................... 5 1.3: POWERNET IPBRIDGE SPECIFICATIONS: ................6 1.4: INSTALLER TOOLKIT COMPONENTS ..................8 2: PHYSICAL INSTALLATION ........................ 9 2.1: MOUNTING THE IPBRIDGE ......................9 2.2: VISUAL STATUS INDICATORS .................... - Page 3 Document Version Date of Revision Revision Author Description 2/06/2013 0.01 Shirl Jones Initial Draft 2/16/2013 0.02 Shirl Jones Initial Review Version 2/20/2013 0.03 Shirl Jones Incorporate Changes from MR and DB 2/26/2012 0.04 Shirl Jones Incorporated Changes from RM 3/14/2013 0.05 Shirl Jones Updated Power Specifications...
-
Page 4: 1: Introduction
IPBR-2 & IPBR-3. 1.1: BEFORE YOU BEGIN The following core tasks are involved when installing an ISONAS IPBridge: 1.Mount the IPBridge in the appropriate indoor location. 2.Supply power to the IPBridge unit. This may be accomplished with power... -
Page 5: General Requirements
Install the ISONAS system in accordance with the National Electrical Code NFPA 70. (Local authority has jurisdiction.) Use only wire or UL-listed cabling recognized as suitable for ISONAS power supply and data communications, in accordance with the National Electrical Code. -
Page 6: Powernet Ipbridge Specifications
1.3: POWERNET IPBRIDGE SPECIFICATIONS: PoE per IEEE 802.3at Input Voltage PoE per IEEE 802.3af 12V DC to 28V DC Current Draw < 0.26 AMPS @ 12VDC < 0.18 AMPS @ 24VDC PoE: 4 Watts Maximum Supplied Power for 1.60 AMPS @ 12VDC External Devices PoE-Plus power (IEEE 802.3at) Maximum Supplied Power for... - Page 7 IPBridge Installation Guide (---Draft---) Page 7...
-
Page 8: Installer Toolkit Components
Before an installer goes to a customer site, they need to put together their supplies and tool-kit. The ISONAS solution is simpler to install than other Access Control Systems, but materials are still needed. And some of those materials may be different than what you are use to carrying. -
Page 9: 2: Physical Installation
2: PHYSICAL INSTALLATION When selecting the location where you are going to mount the ISONAS IPBridge, a few guidelines should be observed. 1) The IPBridge should be protected from extreme heat and sunlight. It is rated for indoor use, between -40 to 80 degrees C. -
Page 10: Visual Status Indicators
2.2: VISUAL STATUS INDICATORS The IPBridge has multiple LED status indicators to assist in monitoring and troubleshooting the status of the unit. LED’s are labeled in Figure 01. LED’s A and B are used to indicate the status of the IPBridge itself. The C & D LED pairs indicate the status of individual doors. -
Page 11: 3: Network
3: NETWORK The IPBridge is connected to the customer’s network using the “Upstream” RJ45 port. The IPBridge network connection auto-detects the speed between 10MB or 100MB, depending on the speed capabilities of the customer’s network. 3.1: NETWORK CONFIGURATION The Crystal Matrix PlugNPlay utility can be used to configure the IPBridge’s network settings. -
Page 12: Daisy-Chaining Network Devices
3.2: DAISY-CHAINING NETWORK DEVICES The IPBridge supplies the functionality of a two-port network switch. It has two physical RJ45 ports or sockets labeled “Upstream” and “Downstream” as shown in Figure 02. The “Upstream” RJ45 port is used to connect to the customer’s network. Some network switches label this as the “uplink”... -
Page 13: 4: Ipbridge Power
4: IPBRIDGE POWER The IPBridge can be powered with PoE, PoE-Plus, or DC power in the range of 12VDC to 28VDC. 4.1: PoE POWER PoE power can used to power the IPBridge itself and is commonly used to provide power to the components at the door, such as an electric lock, a Wiegand device, and/or a passive infrared motion detector. - Page 14 Table A is a worksheet that will help you calculate how much power is available for the daisy chained “downstream” devices. Figure 03 graphically displays the related power flow. Diagram Label Purpose Milliamps Factor Calculated Watts Supplied (mA) (mA) * (Factor) “DC-R”...
-
Page 15: Using Dc Power
If multiple IPBridges are being installed, the 2 IPBridge can be powered with a short coaxial cable such as the one Isonas sells. One end of the cable is attached to connector “BB” on the 1 IPBridge, and then the cable is daisy-chained to connector “AA”... -
Page 16: Common Electrical Connections
4.3: COMMON ELECTRICAL CONNECTIONS 4.3.1: INDEX OF TERMINAL CONNECTIONS External devices are connected to the IPBridge through the screw terminals located on along the sides of the IPBridge. A summary of the purpose of each terminal connection is detailed in the table below. Refer to the IPBridge’s label for the locations of each terminal connector. - Page 17 Terminal Connection Purpose Block Identifier Common Ground Connects with all ground terminals on the IPBridge terminal blocks and coaxial cable Reader Common Ground Connects with all ground terminals on the IPBridge terminal blocks and coaxial cable Reader DC-R Output: Supplies regulated 10 VDC. Reader Not Used Reader...
-
Page 18: 2: Dc Power For The Door Components
4.3.2: DC POWER FOR THE DOOR COMPONENTS The IPBridge can supply DC power for external devices. This power is made available to each door at the terminal connectors labeled “DC” and “GND”. See Figure 06. Figure 06 The voltage supplied by the “DC” terminal connection is determined by the method that the IPBridge is being powered. -
Page 19: 3: Signal Ground Connections
4.3.3: SIGNAL GROUND CONNECTIONS In order for the electrical signals going to the door’s components to function, they need to have a connection to the IPBridge’s Signal Ground. For some doors, only one or two ground wires are needed, and these wires can easily be directly connected to the IPBridge’s “Gnd”... -
Page 20: Door Lock Relay
5.1: DOOR LOCK RELAY The IPBridge is equipped with a lock-relay for each door lock supported. The relay is a Form C relay that is rated for 2.0 amps at 30 VDC. Connections to the relay’s “Normally Closed”, “Common”, and “Normally Open” contacts are available on the terminal strip and are labeled as “NC”, “COM”... -
Page 21: Back Emf Protection For The Lock Circuit
BACK EMF PROTECTION FOR THE LOCK CIRCUIT Most door latches use a relay coil that powers up and down to open and close the door. When power is removed from the coil, the collapse of the magnetic field creates a problem known as Back EMF that can interfere with the IPBridge’s operation, and create radio interference. -
Page 22: 2: In-Rush Current Protection For The Lock Circuit
5.1.2: IN-RUSH CURRENT PROTECTION FOR THE LOCK CIRCUIT Some Magnetic Locks with advanced quick-release circuitry will generate an initial surge of current when the lock is turned on. This surge of current can be 20 times greater than the lock’s steady state current requirements. The lock relay is rated for 2 amp of current. -
Page 23: Ttl Outputs
5.2: TTL OUTPUTS The IPBridge supplies two TTL outputs for each door, as shown in Figure 12. The TTL1 and TTL2 leads are logical output leads. In their “normal” state, there is a 5VDC potential on the leads. When the leads “activate”, this voltage potential is removed (0 VDC). -
Page 24: 1: Ttl's Controlling A Secondary Relay Module
5.2.1: TTL’S CONTROLLING A SECONDARY RELAY MODULE The dual Secondary Relay Module (SRM) is available to enhance the IPBridge’s ability to control devices located at the door. The SRM provides a set of form-C relay contacts, which are controlled by one of the IPBridge’s TTL outputs. -
Page 25: Reader Dc Power Output (10 Vdc)
5.3: READER DC POWER OUTPUT (10 VDC) The IPBridge provides up to 500mA @ 10 VDC regulated power supply for use when powering many Wiegand devices. This 10VDC power is provided on the “DC-R” terminal, and a convenient GND terminal is located adjacent to the DC-R connection. -
Page 26: 6: Ipbridge Door Inputs
6: IPBRIDGE DOOR INPUTS Warning: The IP–Bridge should not be powered until all connections have been made and tested. Remove power prior to changing any connections. The IPBridge can monitor items located at the door. It supports receiving credential data from a Wiegand device and the control of standard electrical locks. -
Page 27: Wiring The Rex Input
6.2: WIRING THE REX INPUT The REX (Request for Exit) signal expected by the ISONAS IPBridge is a momentary closure. You can generate this signal with a pushbutton, infrared motion About REX Input detector, or other simple device. Typically the... -
Page 28: Wiring The Aux Input
This would allow About AUX Input the receptionist to unlock the door using the intercom system’s functionality. In the ISONAS Crystal software you can configure The AUX input is how the door responds to the AUX button. connected to a “Normally Open”... -
Page 29: Wiring The Door Sensor Input
6.4: WIRING THE DOOR SENSOR INPUT About the Door Connecting the ISONAS IPBridge to a door sensor allows the Crystal Matrix software to Sense determine whether that door is physically open. Then the Crystal software can create alarms The door sense is based on the door’s state. -
Page 30: 7: Configuration Examples
7: CONFIGURATION EXAMPLES Several wiring examples are shown below. Please refer to previous detailed sections for more information about each example provided. 7.1: LOCK STRIKE & WIEGAND DEVICE In Figure 20, a standard lock strike is being powered from the IPBridge. The DC power being supplied to the lock is either: 12VDC -- if the IPBridge is powered by PoE or 12VDC. -
Page 31: Magnetic Lock, Rex, Door Sensor, & Wiegand Device
7.2: MAGNETIC LOCK, REX, DOOR SENSOR, & WIEGAND DEVICE In Figure 21, a standard magnetic lock is being powered from the IPBridge. A door sensor and REX button are also being used. The DC power being supplied to the lock is either: 12VDC -- if the IPBridge is powered by PoE or 12VDC. -
Page 32: Lock Strike & Wiegand Device With Tamper
7.3: LOCK STRIKE & WIEGAND DEVICE WITH TAMPER In Figure 22, a standard lock strike is being powered from the IPBridge. The DC power being supplied to the lock is either: 12VDC -- if the IPBridge is powered by PoE or 12VDC. 24VDC -- if the IPBridge is powered by 24VDC. -
Page 33: Controlling Three Doors
7.4: CONTROLLING THREE DOORS In Figure 23, three doors are being controlled. Items of note include: PoE Plus is providing power for all doors Standard lock strikes are being used. 12VDC is powering the lock strikes. Each door has a door sensor switch installed ... - Page 34 The table below describes each door’s connections. Terminal Connection Description Block Identifier Connected to the Door Sensor at the door. Connected to the “DC” terminal, which supplies 12VDC for the locks Connected to the Door Lock Connected to the “COM” terminal to supply DC power to the lock, thru the Lock Relay Provides return for all connections from the door.
-
Page 35: Door & 1 Ip Camera
7.5: 1 DOOR & 1 IP CAMERA In Figure 24, access-control for a single door and an IP-camera are being supported from a single Cat5/6 cable run. A PoE-Plus injector is providing the power required. Items of note include: Connections from the door components are the same as described in example 7.4, including: PoE Plus is providing power for door access and IP camera... -
Page 36: External Power W/Daisy-Chain
7.6: EXTERNAL POWER W/DAISY-CHAIN In Figure 25, the daisy-chaining of two IPBridges is illustrated. External Power is being used, instead of PoE. High-powered PoE could be used, as long as the total power draw across the two IPBridges is under the PoE power limitation. The Ethernet data for both units is supplied with a single network cable connection. - Page 37 For more information: Web: www.isonas.com E-mail: sales@isonas.com Tel: 800-581-0083 (toll-free) or 303-567-6516 (CO) Fax: 303-567-6991 ISONAS Headquarters: 4720 Walnut Street, Suite 200, Boulder, Colorado 80301 USA IPBridge Installation Guide (---Draft---) Page 37...
Need help?
Do you have a question about the PowerNet IPBridge Series and is the answer not in the manual?
Questions and answers