8. Op�cal or electrical sync cable (not included*) *You will need an op�cal sync cable or an electronic flash sync cable with a Nikonos 5 pin connector to connect the Anglerfish Trigger to the remote strobe. Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
A. Menu LED (Red, Blue, Purple) B. Charging LED (Amber) C. Charge complete LED (Green) D. Flash sensors Magne�c switch Nikonos bulkhead c/w cap G. Sea & Sea type op�cal bulkhead H. Velcro �e groove Zip �e groove Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
To wake up the trigger from sleep mode simply hold the trigger in one hand and strike your wrist against your other hand. The impact will Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
Page 9
Shortly a�er, the LED will blue or red) to indicate subsequent impacts blink twice (in are required to fully turn on the unit. By impac�ng the trigger twice more, the trigger turns on. For every impact the Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
Impact once to Wait for 2 blinks Impact twice more wakeup (Red or Blue) to enter on mode To turn off the trigger simply follow the same procedure as required for turning on the unit. Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
Low Battery Indicator conserve power. If the trigger’s batery power is low, the trigger’s menu LED will blink blue for five cycles and the trigger will Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
USB connec�on such as a laptop or a mobile phone. It can also be power with the provided charger adaptor. The charger comes with adaptors for US, EU, Australia and Asia. Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
Op�cal Trigger not Working: If the op�cal trigger does not trigger the remote strobe, remove the fiber op�c cable from the unit and inspect the small high power LED inside the op�cal bulkhead. Operate Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
Page 14
Inspect the bulkhead for debris, salt or fouling. Cleaning the inside of both the remote strobe and the trigger op�cal bulkheads with rubbing alcohol and Q-Tips will ensure maximum light p.10 Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
Physical Dimensions Compliance Anglerfish Trigger: Anglerfish Trigger is constructed from electrical components and parts that are RoHS compliant. Anglerfish is a lead-fee product. p.12 Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
Page 17
For disposal please take this product to a designated electronic waste recycling or disposal area. Charger: The third-party USB charger provided with the Anglerfish Trigger is in compliance with the following regula�ons. p.13 Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
This warranty is void if the device has been opened or tampered with. This warranty does not affect your statutory rights as a consumer. p.14 Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
Page 19
QA/QC Check List PCB Tes�ng & Inspec�on Menu Func�on and Program Test Op�cal Trigger Circuit Test Electrical Trigger Circuit Test Hydrotest (980 kPa) Serial No. p.15 Anglerfish Crea�ve Ligh�ng | Anglerfish Trigger V1.0...
Need help?
Do you have a question about the TRIGGER V1.0 and is the answer not in the manual?
Questions and answers