Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for FLUENT STAGECOMM
- Page 1 STAGECOMM FULL DUPLEX WIRELESS INTERCOM OPERATIONS GUIDE VERSION 17:17...
-
Page 2: Main Features
GENERAL INFORMATION: INTRODUCTION: The STAGECOMM is a multi-purpose Full-Duplex, hands-free communications system that allows up to 5 users to transmit (TX) and receive (RX) simultaneously, with an additional 95 users able to listen-in (RX only). It works by having one transceiver selected as the “Master”, with up to 4 other users that are able to talk... -
Page 3: Transceiver Specifications
TRANSCEIVER SPECIFICATIONS: SPECIFICATION Transceiver Frequency Type ISM 902MHz ~ 928MHz FSK Modulation with Frequency Hopping Transceiver Interface Output Power: Class 1(100mW) Voice Codec 16bit/16KHz TX Max Output Power 100mW RX Sensitivity -95dBm Voice Latency < 35ms Num. of Channels Data Rate 2Mbps Battery Li-ion Battery @3.7V/ TBD 1100mA... -
Page 4: Transceiver Overview
TRANSCEIVER OVERVIEW: 1. Antenna 6. Mode Button 2. Talk / Status LED 7. Talk Button 3. Charging LED 8. On/Off Power Button 4. Volume Controls / Menu Select 9. Headset Jack/AUX In 5. USB Charging Socket... -
Page 5: Step 2: Power On/Off
TRANSCEIVER MENU FUNCTIONS: GRP: (Radio Groups) Groups ID: (Radio ID’s) • This is the handset (Channels) available identification code. The MASTER is always All users must be on the same group set to ID ‘00’ to be able to communicate. •... -
Page 6: Group Selection
GROUP SELECTION: Press and hold the ‘Mode’ button for at least 3 seconds after turning on the device. The ‘GRP’ symbol on the LCD should be blinking. Select the desired group number (00 to 39) by pressing the ‘+’ and ‘-’ 444 on the volume/menu control buttons, then release buttons to establish your selection. -
Page 7: Transmitting And Receiving
TRANSMITTING & RECEIVING: The Master Transceiver will have ID "00", it will remain in Full-Duplex mode (Transmit & Receive) For other Transceivers, press "Talk" button 4 4 for 2 seconds. "TALK" will be displayed on the LCD. To set the unit in Receive Only mode, press the “TALK” button for at least 2 seconds and you will only be able to hear audio. -
Page 8: Receive Only Mode
SIDE TONE ON/OFF: Side tone feature allows you to hear your own voice in your headset earphone. • Press and hold the "Mode" button for at least 3 seconds. • The "GRP" symbol on the LCD will be blinking. Press the "Mode" button two times consecutively. -
Page 9: Battery And Charging
MICROPHONE SENSITIVITY LEVEL CONTROL: You can select the microphone sensitivity at 5 levels depending on your environment. "C1" is the lowest microphone sensitivity and "C 5" is the highest. • Press and hold the "Mode" button for at least 3 seconds. The "GRP"... -
Page 10: Troubleshooting
You may be out of range from other group members. Max range is 1000 feet. Should you have any problems operating your system or if you have any questions regarding your system, please contact us. Fluent Audio Phone: 800 826-2677 e-mail: support@fluentaudio.com... -
Page 11: Warranty Statement
Warranty does not include normal wear and tear on the product or any other physical damage unless the damage was the result of a manufacturing defect. FLUENT AUDIO is not liable for consequential damages due to any failure of equipment to perform as intended. -
Page 12: Repairs And Returns
If it is necessary to return your system for service, you must first be issued a Return Authorization Number (RMA) by our Customer Service Technician prior to sending the system to FLUENT AUDIO. All returns must be prepaid by the sender (no freight collect shipments will be accepted). NO RETURNS WILL BE ACCEPTED WITHOUT A COMPANY ISSUED RMA NUMBER AND PREPAID FREIGHT.