Page 1
Jig Set Instruction Manual We've worked very hard on making this manual useful, simple, and understandable. Please read it carefully, and keep it safe for future reference. ...
WHAT'S INSIDE THIS MANUAL THE ABC'S OF CLAMP AND JIG SET SAFETY 3 Basics of power tool safety 3 Basics of your work area safety 5 Basics of electrical safety 6 Basics of personal safety 7 Basics of servicing your power tools 8 ...
Basics of electrical safety If you are using an electric drill with a power cord, do not modify plugs, ✔ and make sure that the power tools you use correctly match the power ...
Basics of personal safety Don't underestimate the power of safety gear. No one has ever felt sorry ✔ about using safety glasses, gloves, dust masks, non skid safety shoes, hard ...
Pro tip: Take this manual with you to the service point, just in case. NoCry Work & Safety Gear and the manufacturing plant shall not be liable for ...
Wood glue (if concealing pocket holes with included wooden plugs). ✔ Sandpaper or electric sander tool if required. ✔ Phillips head screwdriver to change the jig’s block stop. ✔ Dowel drill guide hole Tightening dial ...
1 Select the correct screw for the job. 2 Set the jig up for use with the appropriate wood thickness ( v ery important!). 3 Secure the workpiece to the jig and workbench using a suitable clamp. ...
Page 14
1” 1 ½ ” 1 ⅛” 1 ½ ” 1 ¼” 2” 1 ⅜” 2” 1 ½” 2 ½” Then, select the correct screw thread and head type. G enerally the type of ...
If you know or regularly work with a certain type of material or workpiece thickness, keep a supply of the matching screw type and length to hand at all ...
When using ¾ inch material thickness Set your jig to the ‘-5/8 in’ mark at S et your jig to ‘1/2 in’ using the the edge of the wood using the side pocket hole indicator arrow. measurement. ...
When using 1 inch and above material thickness S et your jig to the ‘-1 in’ mark at the S et your jig to ‘⅝ in’ using the pocket edge of the wood using the side hole indicator arrow. ...
When using 1 ½ inch and above wood thickness S et your jig to the ‘0 in’ mark at the S et your jig to ‘1 ½ inch’ using the edge of the wood using the side pocket hole indicator arrow. ...
Be sure that your Insert the wooden For a more permanent driven in screws are plug into the pocket hole fix, apply glue around tightened all the way and firmly tap the plug the pocket hole before ...
How to set the drill depth for drilling dowel holes First, select the correct size dowel for the job - this will determine the size of your ...
Page 22
To set the drill collar stop, measure For drilling ⅜ in or ½ in dowel holes, and place a mark slightly over half of we recommend using tape or masking the dowel plug itself, and then align tape around the drill bit to indicate the ...
included F clamp. Multiple clamps might be necessary. To secure the jig set to the workpiece using the provided F clamp… 22 ...
Page 24
Depending on which function you O nce in position, use the arm are using, make sure you have the release lever to slide the moveable correct front block stop screwed onto arm of the clamp to the desired the front of the jig and is flush against ...
Page 25
How to drill the workpiece Before you can finally start drilling your holes (the below example is for pocket holes, but is the same steps for dowel holes), check again that your drill bit is secure in the chuck, that the collar stop correct and fastened, and that you have taken all recommended safety precautions. ...
Pro tip: Practice on scrap pieces of material to get an idea of how the jig works, and how and where to set the stop collar before drilling your pocket holes. How to join two work pieces ...
national inspection and maintenance regulations must be observed. How to clean your jig set For the most part, you'll face the issue of dust or dirt in or around the drill guide ...
HOW TO CONTACT NOCRY Thank you so much for joining the NoCry community with your Clamp and Jig set. If you have any questions or concerns, let us know by writing an email to wecare@nocry.com . ...
Page 34
If you're happy with your purchase, why not spread the word to others who are looking for a clamp and jig set AND h elp us serve you better and grow as a company , by leaving a review on Amazon? To leave a review, go to Amazon > ...