Advertisement
6. operation
warning! ensure you read, understand and apply the safety instructions in section 1 before using the heater.
‰
6.1.
Ensure the heater is at least 1000mm from any object. The heater can be tilted from 0° to 25°, set it to the required angle before
switching the heater on.
6.2.
Plug in the heater and switch it on using the ON/OFF Heat button on the base of the heater, a blue indicator light will flash indicating
that the unit is in stand by mode. Press either the ON/OFF button on the control panel or on the remote to turn the heater on, the blue
indicator light will be on.
6.3.
On models fitted with LED lights, switch on the lights by using the ON/OFF Light button on the base of the unit. A blue indicator light
will flash indicating that the unit is in stand by mode. Press the button again or the button on the remote to switch on the LED's, the
blue indicator light will be on.
6.4.
When the heater or lights are no longer required, switch off using the appropriate ON/OFF button(s) on the base and unplug the unit.
NOTE: When switching off using the remote, the heater and lights will be in stand by mode.
6.5.
The heater has a built in tilt switch safety mechanism that switches off the unit if it is tilted beyond 25° either forwards or backwards.
This prevents fire in the event of the unit being knocked over. If the unit does not turn on again when returned to the vertical, tip it
approximately 25° in the opposite direction until you hear the internal switch operate. As the heater switches on return it to the vertical
position.
7. Maintenance
7.1.
make sure the heater plug is disconnected from the mains supply before any cleaning is attempted. Also allow the heater to cool
completely. do not use water or other liquids, or harsh abrasive cleaners to clean the heater. do not touch the carbon fibre elements
with your fingers as this may damage the tube.
7.2.
clean the exterior with a soft damp cloth and some mild detergent.
7.3.
to replace any of the elements or lamps, contact your authorised sealey dealer.
7.4.
to change the remote control batteries, press down and push back the battery cover (fig.2), remove old batteries and replace with two
new AAA batteries.
warning! do not mix old and new batteries and dispose of old batteries in accordance with local authority regulations.
‰
enVironMent protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
weee regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
battery reMoVal
SEE 7.4
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme. Jack
Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
note: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important: no liability is accepted for incorrect use of this product.
warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
sealey group, Kempson way, suffolk business park, bury st edmunds, suffolk. ip32 7ar
01284 757500
© Jack sealey limited
01284 703534
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
iWMH1809R/LR | Issue:6 (L) 08/09/17
Advertisement
