I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y OVERVIEW Thank you for choosing the 48V/9.6KWh lithium battery system. The battery system is based on a lithium ferrite phosphate chemistry and adopts a modular parallel design.
When installing, using, and servicing this product, please read the manual carefully and follow the safety precautions required in the manual. The safety precautions mentioned in this manual are only intended to supplement local safety regulations. Darfon is not responsible for any injury or loss caused by illegal operation.
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 4 PRODUCT SPECIFICATIONS System Technical Parameters Item description Specification parameter...
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 4.3 Battery Modules 4.3.1 Front Panel Description...
Page 8
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y Parallel A 120 resistor in 2- When multiple battery boxes are machine CAN 3 pins for parallel...
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 5 PRODUCT INSTALLATION Attention The contents of this document may be updated from time to time due to product version upgrades or other reasons.
Page 10
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y Power line UL10269 3AWG 600V Black 1 pcs Used for negative connection...
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 5.2 Before installation This manual contains important information for the installation and safe operation of this product.
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 5.3 System installation 5.3.1 Installation clearance The battery system cabinet can be installed on the floor and wall mount.
Page 13
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y Step 3 - Remove the front door: After opening the side door, the side wall of the front door of the cabinet can see the handle as shown in ①, push the handle up, the front door pops open, rotate the front door 90 degrees to the left, push the front door up as shown in ②...
Page 14
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y Step 6 - Fixed mounting bracket: Place the mounting bracket against the appropriate position wall...
Page 15
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y Step 8 - Install the first battery module: As shown in the figure, place the battery module on the battery cabinet cross member, push it in parallel as shown in ④...
Page 16
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y Step 10 - According to the first battery pack installation procedure, the second, third, and fourth battery packs are sequentially installed, and the...
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 6 ELECTRICAL CONNECTION System Wiring Note: In order to ensure that the lithium battery system can safely and reliably disconnect from the grid, install a separate single-pole or two-stage circuit breaker as a protection device (according to local electrical codes) before the grid is connected...
Page 18
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 6.1.2 Single cabinet wiring Step 1.
Page 19
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 6.1.3 Parallel Cabinet wiring Note: For Cabinet-1 and Cabinet-2 internal wiring please refer to Section 6.1.2 single cabinet wiring steps.
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 6.3 Grounding Connect the grounding point of the battery module to the casing panel.
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 7.3 Host computer description Communication setting parameter table After the cabinets are connected in parallel, insert the RS485 communication interface into the RS485 interface on the front...
Page 24
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y Parallel summary of module information Enter the battery pack information 4, click the current state, you can see the parallel battery pack SLAVE1-8 information and parallel summary information R e v .
Page 25
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y Parallel summary information R e v .
I N S T A L L A T I O N M A N U A L B 0 9 U L F L I T H I U M B A T T E R Y 8 MAINTENANCE AND COMMON TROUBLESHOOTING When you use the product, if it does not work properly, please do not rush to determine that the product is faulty, please refer to the table《Common Troubleshooting Table》...