Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Unpack the Refrigerator
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Remove the Packaging
Remove tape and glue residue from surfaces before turning on
the refrigerator. Rub a small amount of liquid dish soap over the
adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see "Refrigerator Safety."
Dispose of/recycle all packaging materials.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the refrigerator straight out when moving it. Do not wiggle or
"walk" the refrigerator when trying to move it, as floor
damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions
in "Refrigerator Care."
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
INSTALLATION INSTRUCTIONS
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your refrigerator, allow for a
¹⁄₂" (1.25 cm) of space on each side and at the top. Allow for
a 1" (2.54 cm) space behind the refrigerator. If your refrigerator
has an ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed wall,
leave a 2" (5.08 cm) minimum space between the refrigerator and
wall to allow the door to swing open.
NOTE: This refrigerator is intended for use in a location where
the temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature range
for optimum performance, which reduces electricity usage and
provides superior cooling, is between 60°F (15°C) and 90°F (32°C).
It is recommended that you do not install the refrigerator near
a heat source, such as an oven or radiator.
¹⁄₂
" (1.25 cm)
2" (5.08 cm)
3

Advertisement

Table of Contents
loading

Summary of Contents for Whirlpool 30414114

  • Page 1 INSTALLATION INSTRUCTIONS Unpack the Refrigerator Location Requirements WARNING WARNING Excessive Weight Hazard Use two or more people to move and install refrigerator. Failure to do so can result in back or other injury. Explosion Hazard Keep flammable materials and vapors, such as Remove the Packaging gasoline, away from refrigerator.
  • Page 2: Remove And Replace Refrigerator Doors And Drawer Front

    Remove Doors and Hinges Remove and Replace Refrigerator Doors and Drawer Front 1. Unplug refrigerator or disconnect power. 2. Remove the base grille. Grasp the grille firmly and pull WARNING it toward you. 3. Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic.
  • Page 3 Remove and Replace Freezer Drawer Front Final Steps IMPORTANT: Two people may be required to remove and replace the freezer drawer. Graphics are included later in this section. WARNING Remove Drawer Front 1. Open the freezer drawer to full extension. 2.
  • Page 4 Style 1 - Non-Dispenser Models Door Removal and Replacement Top Hinges A. Hinge Cover Screw B. Top Hinge Cover " Hex-Head Hinge Screws D. Top Hinge Bottom Hinges A. Hinge Pin Cover B. Bottom Hinge C. Hinge Screws Leveling/Roller Assembly A.
  • Page 5: Door Removal And Replacement

    Style 2 - External Water Dispenser Models Door Removal and Replacement Water Dispenser Top Hinges Tubing Connection A. Hinge Cover Screw B. Top Hinge Cover C. ⁵⁄₁₆" Hex-Head Hinge Screws D. Top Hinge Bottom Hinges A. Blue Outer Ring Wiring Plug A.
  • Page 6: Electrical Requirements

    WARNING IMPORTANT: ■ All installations must meet local plumbing code requirements. ■ Use copper tubing or Whirlpool supply line, Part Number 8212547RP, and check for leaks. ■ Install copper tubing only in areas where the temperatures will remain above freezing.
  • Page 7: Complete The Installation

    7. Slip the compression sleeve and compression nut onto the Style 2 copper tubing as shown. Insert the end of the tubing into the 1. Unplug refrigerator or disconnect power. outlet end squarely as far as it will go. Screw compression nut 2.
  • Page 8: Install Door Handles

    Handle Installation and Removal Parts Included: Refrigerator door handles (2), Freezer drawer handle (1) Install Drawer Handle Tools Needed: ¹⁄₈" Hex key wrench 1. With the freezer drawer closed, place the handle on the shoulder screws with the setscrews facing down Install Door Handles toward the floor.
  • Page 9: Door Closing And Door Alignment

    ■ Push the base grille in toward the refrigerator until it is firmly in place. Door Closing and Door Alignment IMPORTANT: To comply with American Disabilities Act (ADA) guidelines, fully retract the rollers into the cabinet to lower the refrigerator. Door Closing The base grille covers the leveling screws and roller assemblies located at the bottom of the refrigerator cabinet below the freezer...
  • Page 10: Mise Au Rebut Adéquate De Votre Vieux Réfrigérateur

    Avertissements de la proposition 65 de l'État de Californie : AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de cancers. AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de malformations et autres déficiences de naissance.
  • Page 11: Nettoyage Avant L'utilisation

    Nettoyage avant l’utilisation Après avoir enlevé tous les matériaux d’emballage, nettoyer l’intérieur du réfrigérateur avant de l’utiliser. Voir les instructions de nettoyage dans “Entretien du réfrigérateur”. Importants renseignements à savoir au sujet des tablettes et des couvercles en verre : ¹⁄₂...
  • Page 12 ■ Laisser les portes du réfrigérateur fermées jusqu’à ce vous Réinstallation – Portes et charnières soyez prêt à les détacher de la caisse. Prévoir un support supplémentaire pour la porte du réfrigérateur pendant le retrait des charnières. La force d’attraction des aimants 1.
  • Page 13: Étapes Finales

    Réinstallation de l’avant du tiroir Étapes finales 1. Aligner le système de nivellement/roulettes avec les trous situés de chaque côté de la caisse du réfrigérateur. À l’aide des vis retirées, réinstaller les pièces de nivellement à la base de la caisse. Serrer complètement les vis. AVERTISSEMENT 2.
  • Page 14 Style 1 - Modèles sans distributeur Enlèvement et réinstallation de la porte Charnières supérieures A. Vis du cache de la charnière B. Cache de la charnière supérieure C. Vis de charnière à tête hexagonale " D. Charnière supérieure Charnières inférieures A.
  • Page 15 Style 2 - Modèles avec distributeur d’eau externe Enlèvement et réinstallation de la porte Raccord de tube du Charnières supérieures distributeur d'eau A. Vis du cache de la charnière B. Cache de la charnière supérieure C. Vis de charnière à tête hexagonale "...
  • Page 16: Spécifications Électriques

    Toutes les installations doivent être conformes aux exigences des codes locaux de plomberie. ■ Utiliser un tuyau en cuivre ou une conduite d’alimentation Whirlpool, pièce numéro 8212547RP, et vérifier l'absence de fuites. ■ Installer seulement des tuyaux en cuivre là où les températures resteront au-dessus du point de congélation.
  • Page 17: Raccordement Au Réfrigérateur

    6. Fixer le robinet d’arrêt sur la canalisation d’eau froide avec 5. Vérifier qu’il n’y a pas de fuites. Serrer tous les raccords la bride de tuyau. Vérifier que l’extrémité du raccord du robinet (y compris les raccords du robinet) ou les écrous qui est bien engagée dans le trou de ¹⁄₄"...
  • Page 18: Achever L'installation

    4. Tout en maintenant la poignée, introduire le côté court de la clé à Achever l’installation tête hexagonale dans le trou supérieur, puis tourner légèrement la clé à tête hexagonale pour l’engager dans la vis de blocage. AVERTISSEMENT Risque de choc électrique Brancher sur une prise à...
  • Page 19: Démontage Des Poignées

    3. Introduire le côté court de la clé à tête hexagonale dans le trou REMARQUE : Le fait d’exercer une pression sur le dessus gauche, puis tourner légèrement la clé à tête hexagonale pour du réfrigérateur permet d’alléger le poids appliqué aux vis l’engager dans la vis de blocage.

Table of Contents