Table of Contents
Advertisement
AIR-HYDRAULIC ROLLING JACKBEAM
CAPACITY: 9000 LBS.
MODELS: EELR571A
INSTALLATION AND OPERATION MANUAL
READ ALL INSTRUCTIONS THOROUGHLY BEFORE INSTALLING,
OPERATING, SERVICING, OR MAINTAINING THE LIFT.
6500 Millcreek Drive, Mississauga, Ontario, L5N 2W6
Customer Service 1-800-268-7959
OCT 2016 REV. -
6-4350
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for ALI Snap-on Equipment EELR571A
- Page 1 AIR-HYDRAULIC ROLLING JACKBEAM CAPACITY: 9000 LBS. MODELS: EELR571A INSTALLATION AND OPERATION MANUAL READ ALL INSTRUCTIONS THOROUGHLY BEFORE INSTALLING, OPERATING, SERVICING, OR MAINTAINING THE LIFT. 6500 Millcreek Drive, Mississauga, Ontario, L5N 2W6 Customer Service 1-800-268-7959 OCT 2016 REV. - 6-4350...
- Page 2 1. The Owner/Employer shall ensure that lift operators are qualified and that they are trained in the safe use and operation of the lift using the manufacturer’s operating instructions; ALI/SM 93-1, ALI Lifting it Right safety manual; ALI/ST-90 ALI Safety Tips card; ANSI/ALI ALOIM-2008, American National Standard for Automotive Lifts - Safety Requirements for Operation, Inspection and Maintenance;...
- Page 3 41 – 104 °F (5 – 40 °C). Failure to adhere will result in decertification, loss of warranty, and possible damage to the equipment. Installation of lifts shall be performed in accordance with ANSO/ALI ALIS, Safety Requirements for Installation and Service of Automotive Lifts...
-
Page 4: Table Of Contents
Table of Contents Specifications ......................5 Shipping Contents ....................... 6 Safety Instructions ...................... 6 Position the Jackbeam on Lift ..................7 Operating Instructions ....................9 Storage Position of Jackbeam ................... 11 ... -
Page 5: Specifications
1.0 Specifications Maximum Capacity: 9000 lbs 4082 kg Max. Width Rail to Rail: 45-1/2” 1156 mm Min. Width Rail to Rail: 35-1/2” 900 mm Arms Fully Extended: 56-1/8” 1426 mm Arms Fully Retracted: 37” 940 mm Min Drive Over Height (w/ Pad): 5-5/16"... -
Page 6: Shipping Contents
2.0 Shipping Contents The Jackbeam is fully assembled and packaged to protect it during shipping. Included are the following components: o (1) Jackbeam Assembly, including: Jackbeam Body Lifting Arms with Lifting Pads Air/Hydraulic Pump o (4) Lifting Pad Extension Adapter (2) 3"... -
Page 7: Position The Jackbeam On Lift
4.0 Position the Jackbeam on Lift Lock out and tag out the compressed air supply to the lift. Release the stored air within the unit by draining it by depressing the water drain at the FRL. DO NOT USE YOUR FINGER TO DEPRESS THE DRAIN. COMPRESSED AIR COULD ENTER YOUR BLOODSTREAM AND CAUSE SERIOUS INJURY OR DEATH. - Page 8 5. Raise the lift to a comfortable working height. Check the clearance and movement of the Jackbeam by sliding the Jackbeam forward and backward on the rails. Check that the rollers are centered on the rails at all points along the rail's length. Adjustment of the base arms may be necessary to assure proper operation.
-
Page 9: Operating Instructions
10. Remove the plug with vent breather on top of reservoir to check the hydraulic oil level and fill as need, then replace the plug. 11. Loosen metal knob on the pump by turning counterclockwise before use. See Figure 7. Figure 7- Copper knob on pump 12. - Page 10 2. Position the Jackbeam at the correct lifting points for the vehicle. Refer to the vehicle manufacturer’s literature or, "lifting it right guide" or "vehicle recommend lift points guide" for correct lifting locations. 3. Choose the appropriate pad adapter and ensure it is properly seated into the lifting arm. Extended the lifting arms into position under the vehicle lift points as necessary.
-
Page 11: Storage Position Of Jackbeam
3. NOTE: Lift vehicle at vehicle manufacturer’s recommended pickup points only. Please refer to ALI/LP-GUIDE, Vehicle Lifting Points/Quick Reference Guide for Frame Engaging Lifts. 4. Select lifting points that are the same distance from the centerline of the vehicle, i.e. position the lifting pads so that they make contact at the same point on each side of the vehicle. -
Page 12: Recommended Maintenance
7. As the Jackbeam raises the vehicle, the load on the Jackbeam is transferred from the rollers to the lift. The roller assemblies on the Jackbeam are spring loaded and are meant to carry the weight of the Jackbeam only. When load is applied, the structure cannot be moved. 8. - Page 13 3. Grease upper and lower slider block areas. Use multipurpose, extreme pressure grease such as Megaplex XD%, NGLI grade 2 or other equivalent. 4. Add grease to center hinge nipple, see Figure 10. Figure 10 -Center Hinge Nipple ATTENTION! Discontinue the use of the Jackbeam immediately if any component(s) are damaged, defective, worn or broken.
-
Page 14: Trouble Shooting
9.0 Trouble Shooting Trouble Cause Remedy Pump runs but lift will Lift loaded beyond capacity. Do not exceed capacity of lift list not rise after contacting on tag. load. Fluid leak at pump, hose or Repair leak, refill reservoir. cylinder. Wrong pump installed on lift. -
Page 15: Parts List: Exploded View
10.0 Parts List: Exploded View 15 of 19... -
Page 16: Jackbeam Parts List
11.0 Jackbeam Parts List ITEM# PART# DESCRIPTION QTY. EAK0338T20A HYDRAULIC CYLINDER KIT EAA0417T05A HYDRAULIC CYLINDER -JACK BEAM 9-0592 COUPLER 3/8 NPT MALE 9-0561 FLOW CONTROL F.NPT/JIC-06 EAK0338T21A HYDRAULIC PUMP KIT 1-07789 AIR/HYDRALIC PUMP 9-0666 BRACKET - HYDRAULIC PUMP MOUNTING 9-0667 HEX BOLT M6X1 X16L 9-0558 STRAIGHT UNION 3/8NPT/JIC-06... - Page 17 ITEM# PART# DESCRIPTION QTY. EAK0338T28A TOP FIX END PIN KIT EAM0112T30A PIN - FIXED END TOP FRAME 9-2251 HEX BOLT F/T M8X16 EAK0338T27A ARM STOPPER KIT EAM0112T11A STOPPER - TOP FRAME 9-0553 SPRING WASHER DIA 7 9-0554 HEX BOLT M6X1 16L EAK0338T26A UPPER CYLINDER PIN KIT EAM0112T03A UPPER CYLINDER PIN 9-2251...
-
Page 18: Maintenance Schedule
12.0 Maintenance Schedule Records of all lift maintenance and operator training should be recorded in the following table. Serial Number of lift is located on rear of base. Maintenance and Training Date Notes Performed 18 of 19... - Page 19 Maintenance and Training Performed Date Notes * Make copies of this form as required. 19 of 19...
Need help?
Do you have a question about the Snap-on Equipment EELR571A and is the answer not in the manual?
Questions and answers