Summary of Contents for Qube AP1
- Page 1 Qube Engineering 21914 Palos Verdes Blvd Torrance, CA 90503 818-271-QUBE (7823) art@qube-engineering.com v1.0 © Qube Engineering 2009 © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 1...
- Page 2 18-25 of Qube’s AP1 LED Dash Installation Instructions available from www.qube-engineering.com. Additionally, you will not need to return any core parts to Qube Engineering. © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 2...
- Page 3 LED Array Board Power Connection Cable Fuse Box Power Splitter Color Diffuser Board Screw Cap Removal Tool Cable Ties White Tape Strips Owner’s Manual Waxed Paper Attachment Screws © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 3...
- Page 4 Soldering Iron, Soldering Flux, and Wire Solder Rotary Tool (Dremel) with plastic cutting, grinding, Abrasive, and Cut Off bits Clean Microfiber Compressed Air Glass Cleaner Plastic Cleaner Cloth © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 4...
- Page 5 “unlock” them, bend the ribbons necessary. backwards to straighten the part where the hooks engage them, unhook the ribbon cables, then unplug them. Unlock Bend Unhook © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 5...
- Page 6 Set it aside. -9 dark grey base bulbs -1 black base bulb Set the bulbs aside. © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 6...
- Page 7 Set the the bottom. Set the black plastic frame clear piece aside. aside. © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 7...
- Page 8 16) Remove the yellow and orange color remaining square rubber plugs from the filter plate. Set it aside. plastic housing. Set them aside with the other two square rubber plugs. © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 8...
- Page 9 19) Using small modeling snips or a small rotary tool cutoff wheel, remove the small vertical plastic pieces from the plastic housing. Shown in red. Be careful to leave the pieces not highlighted in red. © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 9...
- Page 10 Caution on the side of cutting less material, as you will still make a final pass with the grinding bit. LIGHT TUNNELS © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 10...
- Page 11 Use the compressed air to blow all remaining dust off of the housing. Make sure to remove any dust from inside the light tunnels as well. The end result should look like this…. © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 11...
- Page 12 Repeat to cover the slits in the 5 remaining the housing. Attach the screws from the light tunnels. An extra tape strip is included. backside as shown. DO NOT OVERTIGHTEN! © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 12...
- Page 13 Only a very light sanding is necessary to expose the wire trace. The wire trace will appear shiny afterwards. © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 13...
- Page 14 AGAIN, DO NOT OVERHEAT THE FILAMENT. Turn off the soldering iron when done with this step. BROWN DARK GREY © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 14...
- Page 15 38) Turn the gauge cluster assembly back one black based bulb as shown. over. Reinstall the four black template pieces onto the gauge cluster assembly. EMPTY BLACK DARK GREY © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 15...
- Page 16 Install it in the gauge cluster housing, color filter side up. © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 16...
- Page 17 Use the compressed air to remove any dust between the two pieces. © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 17...
- Page 18 © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 18...
- Page 19 The Screw from the middle of the lower portion of the gauge cluster is no longer used. DO-IT-YOURSELF SUPPLEMENTAL INSTALLATION COMPLETE! Please continue on to step 26 in the AP1 LED Dash Installation Instructions. Enjoy your new LED Dash! © Qube Engineering 2009 Qube’s AP1 LED Dash DIY Kit Supplemental Instructions Page 19...