Advertisement
Quick Links
KB-M2-WMT- _ _ , KB-R2-WMT- _ _ , and KB-R3-WMT- _ _ Series
1.
Cut or drill mounting pattern in panel using the provided cutout template. Refer to Figure 1 for the panel mounting
pattern.
NOTE: +/- 0.8 mm (0.03") tolerance on all dimensions unless otherwise noted
The provided hardware is for use with panels that have a maximum thickness of 6.4 mm (1/4") if using
clearance holes. Thicker panels can be used but require 1/4-20 tapped holes or longer screws than
those provided. For thicker panels or panels where rear access requires a second person, you must
install the plastic bulkhead fitting onto the left hand wall bracket first (as shown in steps 7 and 8), and
then proceed from step 1.
38.1 mm
11.1 mm
(1.50")
(0.438")
Ø
76.2 mm
(3.00")
31.8 mm
(1.25")
FIGURE 1 – PANEL MOUNTING PATTERN
2.
Install the left hand wall bracket first using four of the provided 1/4-20 screws, washers, and nuts as shown. Tighten
all screws until the gasket is compressed to 1/16" to 3/32" thick.
RUBBER WASHER
NUT
GASKET
FIGURE 2 – SIDE VIEW AND FRONT VIEW OF LEFT HAND WALL BRACKET
99109A • December 16, 2019 • www.HopeIndustrial.com • International: +1 (678) 762-9790 • UK: +44 (0) 20 7193 2618 • © 2020 Hope Industrial Systems, Inc. • Page 1 of 4
Installation Instructions
Wall Mount Folding Keyboard
31.8 mm
(1.25")
450.85 mm
(17.75")
+ 2.3 mm (0.09")
- 0.8 mm (0.03")
NYLON WASHER
1/4-20 SCREWS
1/4-20 SCREWS
LEFT HAND WALL BRACKET
Ø
8 mm (5/16") DIAMETER
OR 1/4-20 TAPPED HOLES
(PREFERRED FOR EASIER
INSTALLATION) (8 PLACES)
25.4 mm
(1.00")
PLACE 44" OFF FLOOR
FOR MOST UNIVERSAL
ERGONOMIC HEIGHT
Advertisement
Summary of Contents for HIS KB-M2-WMT Series
- Page 1 Installation Instructions KB-M2-WMT- _ _ , KB-R2-WMT- _ _ , and KB-R3-WMT- _ _ Series Wall Mount Folding Keyboard Cut or drill mounting pattern in panel using the provided cutout template. Refer to Figure 1 for the panel mounting pattern. NOTE: +/- 0.8 mm (0.03") tolerance on all dimensions unless otherwise noted The provided hardware is for use with panels that have a maximum thickness of 6.4 mm (1/4") if using clearance holes.
- Page 2 Wall Mount Folding Keyboard Installation Instructions (continued) Loosely install the right hand wall bracket using only 1 of the provided 1/4-20 screws, washers, and nuts in the location shown. The remaining three screws will be installed after fitting the keyboard in place. RUBBER WASHER NYLON WASHER 1/4-20 SCREW...
- Page 3 Wall Mount Folding Keyboard Installation Instructions (continued) Swing the right hand wall bracket into place, trapping the keyboard as shown. RIGHT HAND WALL BRACKET FIGURE 5 – FRONT AND SIDE VIEWS Finish installing the right hand wall bracket using the remaining three 1/4-20 screws, washers, and nuts. Tighten all screws until the gasket is compressed to 1/16"...
- Page 4 Wall Mount Folding Keyboard Installation Instructions (continued) Insert the cable and fitting through the hole in the left hand wall bracket. Tightly reinstall the nut from the rear. Push the cable through as far as it will go, then tighten the cable gland nut from the front. IMPORTANT! FAILURE TO FULLY TIGHTEN EITHER NUT WILL COMPROMISE THE WATERTIGHT SEAL ON THE PANEL.