Krug & Priester EBA 4315 Manual

Krug & Priester EBA 4315 Manual

Guillotines

Advertisement

Guillotines
EN Operating Instructions
EBA 4315
EBA 4350
www.eba.de

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EBA 4315 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Krug & Priester EBA 4315

  • Page 1 Guillotines EN Operating Instructions EBA 4315 EBA 4350 www.eba.de...
  • Page 2: Table Of Contents

    Table of Contents Safety precautions Intended use Installation Startup Operation Operating elements Blade and cutting stick replacement Maintenance and cleaning Annual inspection / Safety test Possible malfunctions Accessories Technical data EC-declaration of conformity - 2 -...
  • Page 3: Safety Precautions

    Safety precautions Please read these operating instructions before putting the machine into operation and observe the safety precautions. The operating instructions must always be available. Children must not operate the machine! Do not reach beneath the blade! Never leave the blade unattended! Do not extract or transport the blade without protection! (See page 24 and 26).
  • Page 4: Intended Use

    Safety precautions / Intended use Do not use any spray cans with flammable content near to the cutting machine! Do not use any flammable cleaning agents. Intended use The machine is designed for cutting stacks of paper to a specified size. This machine is constructed for "one-man operation"...
  • Page 5 Safety precautions Disconnect from the mains before starting any service work or before removing the panels! Replacement of blade and cutting stick may be performed only when the main switch is switched off! - 5 -...
  • Page 6 Safety precautions All components which could endanger the operator are covered by a guard! Operating the machine without safety device is forbidden! • Movable front safety guard (A) • rear screwed safety guard (B) • and cover (C) - 6 -...
  • Page 7 Safety precautions The dangerous cutting movement is safeguarded by a movable guard (A), rear screwed safety guard (B) and a safety two-handed control system! (C) Before working with the machine and after every blade replacement the automatic cut-off function of safety guard (A),(correct if distance between cover and table is <...
  • Page 8 Safety precautions Protect mains cable against heat, oil and sharp edges! Connect the power cord to a single phase 230 V / 10A min socket. 120 V / 15A min Ensure free access to mains - 8 -...
  • Page 9 Safety precautions When not in use for a longer period switch off (Main switch to "0"). Danger! Do not turn main switch to position "0" whilst blade is moving upwards or downwards! Risk of injury! Danger! Blade must always be covered by the pressing bar.
  • Page 10: Installation

    Installation Unpack the cabinet (A), (accessories) or stand (B), (accessories) and assemble according to the enclosed separate instructions. 2 strong people are required to lift the machine onto the cabinet. Beware of fingers! Do not hold onto the actuators (B) when lifting the machine out of the packaging! The operating side of the machine must align with the cabinet (A)!
  • Page 11 Installation Assembly of stand: 2 strong people are required to lift the machine out of the packaging. • Lay the machine on the floor side wards (1.). • Remove the lower cover (2.) • Place the cutter correctly onto the machine stand.
  • Page 12: Startup

    Installation / Startup Screw on the backgauge crank (A). Screw on the handle (B) (only 4315) found in the tool set (C). Startup Plug into socket. - 12 -...
  • Page 13 Startup It is forbidden to operate the machine if the operating and safety instructions have not been understood. Please check the safety devices are functioning and complete before use. • All covers have to be mounted (A). • The release for cutting is allowed only if the cover is closed and the two-hand safety device is operated at the same time (B).
  • Page 14: Operation

    Operation Position the main switch "I" (A) Insert the key the control system and move it to the right (B). Open the safety guard (C). The machine is now ready for use. - 14 -...
  • Page 15 Operation The measurement is set with the backgauge crank.(A) The symbol – rotary direction – moves to the right on the display (B) (see picture C). The rotary direction of the backgauge crank (A) is indicated on the right. Keep turning the backgauge crank to the right until a measurement appears (see picture E).
  • Page 16 Operation Optical cutting red line (A). Blade cuts on the front edge (B) of the light beam. (Only use when no exact cut is required). Pull out the handle to avoid the measurement being wrongly adjusted. - 16 -...
  • Page 17 Operation Position the paper on the backgauge (A) and the side lay (B). To move paper stacks, please use the paper knock-up block (C). Run backgauge to the front for turning the paper stack. Close the safety guard. - 17 -...
  • Page 18 Operation 4315 Before every cut the lever must be moved to the left and tightened with light pressure. 4350 The clamp moves automatically when cutting is activated. Cutting activation: Press both buttons of the two-handed control system (A) simultaneously and keep them pressed until the paper is completely cut.
  • Page 19: Operating Elements

    Operation / Operating elements Operating elements - Front safety guard - Safety two-handed control system - Overload switch blade drive - Clamping - Main switch - Crank handle for backgauge setting - Key switch - Backgauge - Side lay left - Display cutting size (cm or inch) - Changeover cm/inch - Measuring unit (cm or inch)
  • Page 20 Operation Start machine • Main switch to position "I", insert the key for the control panel and turn it to the right. Open the front safety guard Warning! Before cutting a measurement please check if the correct scale (cm or inch) is set. Display in cm or inch •...
  • Page 21 Operation Cutting to specified dimensions • The cutting size can now be set with the handle • Insert paper and move by means of the stacking angle to the backgauge side lay on the left • Move the pressing lever to the left by a slight swing (only 4315).
  • Page 22: Blade And Cutting Stick Replacement

    Blade and cutting stick replacement If the cutting quality decreases: • Check the cutting depth (see page 30). • Check the cutting stick (see page 23). • Replace or grind the blade (see page 22 - 30). The blade cannot be ground if the blade height is less than 35 mm/1,38 inches.
  • Page 23 Blade and cutting stick replacement Turn the blade depth adjustment screw to the left until it stops (screwdriver found in tool set (A). Cutting stick replacement : • Lift the cutting stick by hand and pull it out.(1.). • If needed the cutting stick can be turned or exchanged.
  • Page 24 Blade and cutting stick replacement Position the main switch to "0" (1.) Open the safety guard (2.). Remove the 2 blade screws on the elongated holes (3.). Then put the blade changing tool (R) into place and fasten it to the blade (4.). Remove the remaining 3 screws (1.).
  • Page 25 Blade and cutting stick replacement Take the exchange blade carefully out of the blade box and screw it to the blade changing tool (A) • blade must be covered! (B). Danger! Risk of injury! - 25 -...
  • Page 26 Blade and cutting stick replacement Place the blade to be exchanged, using the blade changing tool, into the blade carrier and push to the top and to the left.(1.) (see picture A) while doing so push both springs back. It is only necessary to push back the springs if a polished blade is to be exchanged.
  • Page 27 Blade and cutting stick replacement Push the blade changing tool to the top with your hand (1.). First, lightly tighten the middle blade screw with your other hand (2.) and then both blade screws left and right (3.). Remove the blade changing tool (R) (unscrew the grips).
  • Page 28 Blade and cutting stick replacement Open the clamp by moving the clamp lever to the right (1.). Remove all tools and distribute paper along the entire cutting length (2.). Turn main switch to position "I" (3.). Close the clamp by moving the clamp lever to the left (1.) Close the safety guard (2.) Lower the blade by pressing both cutting buttons (3.) If the last sheet of paper is not completely cut,...
  • Page 29 Blade and cutting stick replacement Tighten all 5 blade screws. - 29 -...
  • Page 30 Blade and cutting stick replacement Paper cutting test. If the last sheet or several sheets are not completely cut, gradually turn the knob for blade depth adjustment (A) ¼ turn to the right until the paper is cut along the entire length. Do not set too low as blade will become blunt sooner.
  • Page 31: Maintenance And Cleaning

    Maintenance and cleaning Maintenance work may only be performed by trained staff. Danger! Disconnect the mains before starting any service work or before removing the cover. Annual inspection Next Maintenance To maintain the operational safety and to prevent premature wear, we recommend an annual inspection and maintenance of the machine by a qualified service technician.
  • Page 32 Maintenance and cleaning = Greasing points on the machine. No. 9800 933 No. 9001 828 Grease the backgauge (A) guide weekly. (Use non-resinous grease). Grease the remaining parts (B) twice a year (see picture). Danger! Disconnect the mains before starting any service work or before removing the cover.
  • Page 33: Possible Malfunctions

    Possible malfunctions Machine does not function! Is the machine plugged in? Main switch to position "I"? (A) Control system activated? (B) (Turn key to the right) Release a cut see page 18. - 33 -...
  • Page 34 Possible malfunctions Machine turns off: • Machine overloaded Safety button (A) ejects. Allow 1 minute cooling time and reset the safety button (A). • Machine blocked • Blade is blunt Eliminate the cause, and push the safety button (A). - 34 -...
  • Page 35 Possible malfunctions Does not cut through the last sheet: • Turn or turn around the cutting stick (A), readjust the blade by means of the blade adjusting knob (B). (See page 30). Poor cutting quality or blade stays in the paper stack.
  • Page 36 Possible malfunctions Cut cannot be made. • If cover is open: close • If cover is closed: open and re-close it. (Security check). Motor runs but blade does not move downwards. • Security brake has been activated! Inform the service team! Did none of the specified solutions help Service you with your problem?
  • Page 37: Accessories

    Accessories Recommended Accessories: Blade No. 9000 121 Cutting stick (6 pieces) No. 9000 221 Paper knock-up block No. 9000 520 Blade changing tool No. 9000 522 Cabinet No. 4215 1100 Stand No. 4205 1100 Included in delivery. - 37 -...
  • Page 38: Technical Data

    Technical data Technical data: • Power supply: 230V/50Hz/0,45KW, 120V/60Hz/0,45KW • Sound level: EN 13023: < 70 dB (A) • Leakage current < 3,5mA • Power cord gauge min. 1,5mm (230V) • Power cord gauge AWG 18 (15A) (120V) • Cutting height: 40 mm •...
  • Page 39 Technical data This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 2006/42/EG, and 2014/30/EU. Sound level information: The sound level is < 70 db (A) as defined by EN 13023. Subject to alteration without notice. - 39 -...
  • Page 40 Technical data The company Krug + Priester has the following certifications: • Quality management system according to DIN EN ISO 9001:2015 • Environmental management system according to DIN EN ISO 14001:2015 • Energy management system according to DIN EN ISO 50001:2011 - 40 -...
  • Page 41: Ec-Declaration Of Conformity

    EC-declaration of conformity EC-declaration of conformity - Herewith we declare that GS- IDENT. No. UL- IDENT. No. 4315 11431501 10431501 4350 11435001 10431501 - complies with the following provisons applying to it 2006/42/EG: EC Machinery directive 2014/30/EG: EMV Electromagnetic compatibility directive 2011/65/EU, 2015/863/EU RoHS directive - Applied harmonised standards in particular...
  • Page 42 Remarks: - 42 -...
  • Page 43 Remarks: - 43 -...
  • Page 44 EBA • Made in Germany • Document Shredders • • Trimmers and Guillotines • Krug & Priester GmbH & Co. KG Simon-Schweitzer-Str. 34 D-72336 Balingen (Germany) www.krug-priester.com 9700193 9700136 01-2020 24.01.2020 zm...

This manual is also suitable for:

Eba 4350

Table of Contents