Page 1
We take all possible measures to make this document, however, if there is any suspicious point, error, omitting erroneously, please kindly contact us. This product is under development. Specifications might be changed. Nippon Primex Inc. Sales by Nippon Printer Engineering Inc. Manufactured by D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 2
Revision History Contents of Revision Person in Rev. Approval Page Item Contents of Change charge 0.01 Release(Provisional) Suzuki 2013.10.31 2013.10.25 D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 3
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference Under Review received, including interference that may cause undesired operation. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 4
● Please do not block the paper outlet while print operation. Also, please do not grab the paper while print operation. ● Paper may adhere after paper ejection due to environmental condition of static electricity when installation of this product. Please consult us for reviewing removal of electricity. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 5
● A part of this product is made from coated steel plate. It does not affect the product’s quality and performance at all even if the cut face of the steel plate get rusty after a long time period. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 6
● The coverage of warranty is limited within the product itself, Nippon Primex Inc. is NOT responsible for anything induced by the defect of the product and DO NOT pay for any compensation that may occur.
Overview 1.1 Application This document is applied for NP-2651/3651 This specification is forNP-2651/3651. (Please pay an attention that usable paper or character type, power supply or environment may differ from other models.) [Note] ・Please refer to other specifications for option etc.
14) Easy maintenance by a complete openable thermal head. Easy to remove jammed paper. 15) Various option items are available. 16) Tension Bar is mounted. *1:Only Ubuntu was verified. *2:Description [F/W] indicates [Firmware] hereinafter. *3:Please refer to [1.5 Options]. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
NP-2651D [Default condition] 2) NP-3651D(Standard) Configuration of the product is as follows. Configuration Name Specifications Quantity 3inch,USB/Serial Round shape power NP-3651D connector Label print [Note] ・No attached article. No sample label paper. NP-3651D [Default condition] D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 11
1.5 Option 1) Power Supply PS8 DC24V Output adapter is prepared. Please refer to product specifications D-F10058. [Note] ・When operating high print ratio printing, please verify it with actual printer to use beforehand. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Quadruple Bold Print Double Print Inverted 90°clock-wise rotation Underline 4:Linefeed q’ty(default) 4.25mm (1/6inch) *1:It is required for change etc. by command. *2:Print speed varies depending on conditions. *3:KS X 1001:1992 built-in font. *4:Changeable by command. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 13
Weight (12pcs) (12pcs) *5:Default status is Line mode. Page mode is available by switching command. *6:Please make sure to use this product with install position: Horizontal. Please do not use with the other install position. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
・Default setting paper width of NP-2651 is 58mm, NP-3651 is 80mm. ・When changing paper width to 60mm with NP-2651, please refer to [How to change the paper width of NP-2651 58mm→60mm].
Page 15
・Please consult us if paper holder for φ102mm. (It is treated as OEM) ・Please regard the O.D. value of paper near end detection as the indication value since it fluctuates depending on paper type or paper thickness. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
3mm, print may deviate due to paper bias. *2:Please refer to [How to change paper width 58mm→60mm of NP-2651] for change of paper width. *3:Please refer to [How to change paper width 80mm→76mm of NP-3651] for change in paper width.
Page 17
3) How to Change the paper width [How to change the paper width of NP-2651 58mm→60mm] Before Change: (1)Move Guide Open Thermal head cover. Paper Width 58mm(Default) Guide Paper table interspace Interspace Bracket Set boss. Guide (No Float) Shaft Please move guide at the...
Page 18
*Please beware of no floating or bending of guide and no loosening Screw. After change Paper width 76mm [Note] ・When paper width 80mm, the side to attach arm is changeable. Please refer to (2). D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
40±0.5mm(NP-3651) [Note] *D dimension does not change even if paper width changed to 60mm with NP-2651. *D dimension does not change even if paper width changed to 76mm with NP-3651. 1) Cutting Method:Slide System :Full Cut / Partial Cut A / Partial Cut B...
Sensor(2) specs: Sensor(1) treated as OEM [Note] *Remove dust, paper powder etc. on sensor periodically. *Dark pre-print is prohibited by 7.5mm left or right from standard position. Please have enough verification when using pre-print paper. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
2) Label paper transmission sensor position A(±1mm) B(±0.5mm) C(±0.5mm) 11.5 mm 29.9 mm 58.0 mm NP-2651 11.5 mm 29.9 mm 60.0 mm 11.5 mm 36.3 mm 76.0 mm NP-3651 11.5 mm 40.3 mm 80.0 mm D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Connect following connector for this connector(Power supplied externally) Connector at printer side : S2P-VH(LF)(SN) JST or equivalent. Connector at adaptor side: VHR-2N JST or equivalent. Function +24V Connector Fig.(Interdigitation view) 2) Power Supply Voltage :DC24V±5% D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 23
2200μ between power supply and ground. Please wire not to electromagnetic effect to power supply line and signal line of printer due to other power supply line, etc. Also, please use withstand voltage: 35V or more. ・Please use LPS power supply as recommended. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Specification for label paper: HW76B Print density : 100% Use environment: Normal Temperature and humidity [Note] ・If using other paper than recommended paper, life duration may be shorten. 2) MTBF(Mean Time Between Failure) *.*×10 hours D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Please confirm in customer side. 2.8.2 Storage Environment (Except paper) Temperature: -30~70 degree Humidity : 10~90%RH Non Condensation High Temperature and humidity: 40 degree 90%RH(no condensation)as the worst. 2.8.3 RoHS This product is RoHS compliance. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Regulations of this product are as follows: NP-2651 NP-3651 Remarks CEmark Under review Under review UL60950-1 Acquired Acquired VCCI Under review Under review Under review Under review *1:If the appearance differs from standard, it is not applicable to UL. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
・Form may differ depending on communization of parts and improvement except the part described its external dimensions, attachment hole, or paper Outlet dimensions, etc. ・This is figured for NP-2651, a dual interface type of Serial, USB connector. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 28
・Form may differ depending on communization of parts and improvement except the part described its external dimensions, attachment hole, or paper Outlet dimensions, etc. ・This is figured for NP-3651, a dual interface type of Serial, USB connector. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
*1: Please use either one of the following drivers, or newer version. (NPI EX driver and newest is recommended) Subsequent NPI EX Driver Ver.2.0.0.0 Subsequent NPI Printer_DS2.0 *2: Receive Buffer Remaining Size auto-reply format(When MS2-7:OFF) 〔FF〕h+〔01〕h+〔00〕h+〔00〕h+〔00〕h+n *〔00≦n≦0F〕h n=receive buffer remaining size(0~15K Byte) D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
*4:Occurs when turning the power OFF or during self-diagnostic print and while software reset or when receive buffer full or after receiving memory switch setting command or when rewriting firmware. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
- Signal GND Connect cathode emitter. [Note] *If you connect exterior paper near end sensor with non-standard paper holder, please confirm sensor specifications well before use. *This connector is connected with standard paper holder(UPH-Arm_W_Unit). D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 32
Back side view Pin No.1 side Pin No.1 Pin No.5 Pin No.6 (When Dtype) Pin No.9 Bottom side view *When 2pin power connector selected, CN1:round type becomes CN9:2pin. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Serial Baud Rate DS1-4 DS1-5 115200 38400 19200 9600 DIP switch is mounted on the printer bottom. Dip switch DS1 DIP switch ON side DIP switch not mounted here. DS1-1side DS1-8 side DIP switch OFF D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 34
・Please set MS2-5, MS2-6, MS2-8 always OFF fixed. ON setting may cause malfunction. Table 3 Built-in Language Font Built-in font MS2-2 MS2-3 Japanese Chinese Korean Greek [Note] ・Please refer to command [Character Code Table Selection] 《ESC t n》 for other languages font. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
(Set paper at the same time.) (5) Memory switch content is printed and confirm it. [Note] ・Please make sure to return DIP switch. ・In case of cancelling a mode of writing memory switch, please keep thermal head cover closed. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Once detects paper out, paper end status is transmitted and stop printing. Please do not use paper roll whose end is glued to core. It causes no detection. Please change roll paper promptly once detecting out of paper. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
[LineFeed Amount Setting of the Smallest Paper Feed Pitch ] < ESC 3 n > *1 Buffer full data number(Maximum print digit number) differ depending on each size of ANK・Japanese Kanji (Please refer to [2.1.2 Print specifications]). D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
No switch (Only half size) Russian No switch (Only half size) Scandinavian No switch (Only half size) Turkish No switch (Only half size) *1:00h ~ 1F h cannot be printed because those are control codes. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Examples for detection are as below. (1) Detection forward direction(In case the next gap sensor does not exceed sensor) Label 2 Cover Paper feed direction Detect feeding forward direction Transmission sensor Label 1 Print head D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 40
The following problems may occur when detection to reverse direction. Examples for occurring problem and workaround plan when using label paper with 3mm gap are as below. Status before detection Cover Label 2 Transmission sensor 8.5mm Paper Feed Direction 6.5mm Head Label 1 D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 41
・Example for workaround plan is as below. *1: by 2mm interference at tip of cover and terminal of label paper, terminal of label paper may get stuck with tip of cover and may peel off. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 42
*2:Printing is until the position that terminal of label 1 does not exceed the tip of cover. 7.5mm or more of remaining amount is recommended although 6.5mm or more is required. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 43
*3: When back feed is conducted by command for redetection of gap, enough distance which gap reach to transmission sensor is required before the terminal of label 1 interfere the tip of cover. 6mm or more is recommended. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 44
11.5mm or more depending on cutting position. ・It is recommended to skip a piece of label paper for gap detection after cutting and conduct forward detection. ・Please confirm firmly at user side when detection to reverse direction of gap.with cut. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
It requires setting it again when executing RESET because printer will return to same status as turning the power on. Please make sure that data will be deleted when data remains in the buffer memory. Side view ALARM FEED SW RESET D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
UPH-Arm_W_Unit Winding Paper roll Print side [Note] ・Please do not deliver while paper roll is set. ・Please do not apply excessive force to UPH-Arm_W_Unit when setting and unsetting paper Roll. It may cause any failure. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 47
・Please make sure to conduct auto-loading after conducting setting command for label when using different paper. Please refer to command reference for command. Paper edge form × × ○ Label 1 Label 1 Label 2 Label 2 Label 1 D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
Page 48
・In the incident of inserted paper on the bias, please open the head cover and straighten the paper. (Paper must not be deviated from paper guide.) Please press plate to close thermal head cover instead of head open lever. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
・Please pay an attention to fingers and hands when a thermal head cover closes. ・Please clean up and set paper when glue adhere onto thermal printer head, cutter, and around printer head. Head Open Lever D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
・The operation 4.8.2) or level adjustment by command will be required when reading gap between paper does not work after cleaning. Transmission sensor Thermal Head Paper Near End Sensor Paper out sensor Paper out sensor Transmission sensor Auto-cutter Paper near end sensor Platen D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)
・Please design this product not to interfere from exterior components. If exterior components interfere, it influences print and cut function and causes breakage of this product. D-F10137 NP-2651/3651 Product Spec. Rev.0.01(Provisional)