SAFETY INFORMATION WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions Important - Please read these instructions fully before starting assembly may result in electric shock, fire and/or serious injury. General Power Tool Safety Warnings Save all warnings and instructions for future reference.
Page 3
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is Important - Please read these instructions fully before starting assembly unavoidable, use a residual current device (RCD) General Power Tool Safety Warnings protected supply.
Page 4
4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off.
TACKER SAFETY WARNINGS 1. Always assume that the tool contains fasteners. Careless handling of the tacker can result in unexpected firing of fasteners and personal injury. 2. Do not point the tool towards yourself or anyone nearby. Unexpected triggering will discharge the fastener causing an injury.
Page 8
SYMBOLS To reduce the risk of injury, user must read instruction manual Wear eye protection Wear ear protection Wear dust mask Warning Double insulation Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice. EN-8...
COMPONENT LIST 1. TRIGGER 2. MAIN HANDLE 3. POWER CABLE 4. STAPLE MAGAZINE 5. CONTACT SWITCH 6. KNOB FOR HAMMER FORCE PRESELECTION 7. ON/OFF SWITCH 8. MAGAZINE LOCKING LEVER TECHNICAL DATA Rated voltage 220-240~ 50Hz Impact rate 30 /min Standard staple size range 15-25 mm Brad nail size range 15,20,25,30,32mm...
NOISE / VIBRATION INFORMATION A weighted sound pressure = 80,48dB(A) = 3.0dB(A) A weighted sound power = 91,48dB(A) : 3.0dB(A) Wear ear protection when sound pressure is over: 80dB(A) Vibration Information Vibration total values (triax vector sum) determined according to EN60745: Hand arm vibration Vibration emission value a = 2.13 m/s...
Page 11
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. Intended Use The power tool is intended for tacking fabrics, leather, card board, foils, insulation material and other materials to soft structural surfaces, such as wood or wood-like materials. The power tool is not suitable for fastening wall or ceiling panelling.
2. HAMMER FORCE PRESELECTION (SEE FIG B) With the knob for hammer-force preselection, it is possible to preselect the required hammer force. The required hammer force depends on the length of the staples or nails, and on the strength of the material.
TROUBLESHOOTING Problem Possible cause solution 1. product does not start 1.1 not connected to power supply 1.1 connect to power supply 1.2 product no switch on 1.2 switch ON 1.3 power cord or plug is defective 1.3 check by a specialist 1.4 other electrical defect to the electrician product...
Page 14
PLUG REPLACEMENT (ONLY FOR REWIRABLE PLUG OF UK & IRELAND) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE – NEUTRAL BROWN –...
PO Box 6242, Newbury, RG14 9LT, UK Declare that the product Stapler Gun Description: Type PCT162 (CT-designation of machinery, representative of staple gun) Function tacking fabrics, leather, card board, foils and so on Complies with the following Directives: 2006/42/EC, 2014/30/EU, 2011/65/EU...
Need help?
Do you have a question about the PCT162 and is the answer not in the manual?
Questions and answers