Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Slootsmid SF 6
- Page 1 Slootsmid Mercerator SF 6, SF 6 , SF 8, SF 8 en SF 10...
-
Page 2: Table Of Contents
11. Tuning ...................................... 10 12. Assembly and disassambly .............................. 11 13. Maintenance ..................................12 Attachment I: Hydraulic scheme Attachment II: E-motor en coupling when electric driven Slootsmid Mesttechniek B.V. Korenbree 40a NL-7271 LH Borculo Telefoon: +31 (0)545-273859 E-mail: info@slootsmid.com Internet : www.slootsmid.com... -
Page 3: Introduction
Before you start working with the macerator we strongly advise to read this manual carefully, we cannot give any guarantee on inappropriate use or handling. Slootsmid is always trying to improve their products and is therefore aloud to change the device at any moment without further liabilities to former sold devices. - Page 4 (Regulation 89/302/EEG) Manufacturer: Slootsmid Mesttechniek B.V. Adress: Korenbree 40a, NL-7271 LH Borculo (The Netherlands) Herewith declares that, The SLOOTSMID MACERATOR type SF 6, SF 6E, SF 8, SF 8E and SF 10 Serialnumber __________________________________________ Year of construction __________________________________________ Date of delivery __________________________________________ Meets the requirements of the Machinery regulation 89/392/EEG as recently changed;...
-
Page 5: Safety Measurements
7. Watch out for your fingers when repairing the cutting rotor. 8. Damaged hydraulic lines must be replaced immediately 9. It is not allowed to modify the gauge pressure valves. Ask your dealer or Slootsmid! 10. Never stand on the device when working with the device. -
Page 6: Safety Stickers
5. Safety stickers The on the device attached stickers give information for a safe working with the device. Damaged stickers need to be replaced! Attention! Read the manual and safety measurements before you start working with the machine! Attention! Watch your fingers when repairing of working with the cutting rotor. -
Page 7: Technical Parameters
Connection 6” Weight 80 kg Capacity 3.5 m³/min Hydro motor EPMS 125 Necessary hydraulics 30 till 40 Litre, maximum at 150 bar Type SF 6 E Length 530 mm. Width 330 mm. Height 530 mm. Connection 6” Weight 80 kg Capacity 3.5 m³/min... -
Page 8: Usage
Massa (kg.) 9. Assembly The Slootsmid macerator is placed before the pump of vacuum tanker in the suction line. It is attached with flanges (pay attention to packing seal). The macerator can be placed in every position, only make sure that the hydro- or electro-motor is never placed on top! This will damaged the bearing. Also never assembly the macerator with the cover to the top, this can realize that heavy parts stay on the rotor. - Page 9 Because of the rotor and flow of the manure there is hardly any pressure difference. When attaching the hydro motor pay attention to the correct way it turns (see images below). The hydro motor works optimal when the oil flow is 40 litres per minute. Pay attention to the diameter of the hydraulic lines.
-
Page 10: Starting Up
10. Starting up Before the macerator is put in to use first check all the connection bolts and lines, these have to tightened. Then put on the hydraulic charge. In the macerator a soft rubbing noise can be heard. When a loud noise occurs stop the macerator immediately (see tuning). -
Page 11: Tuning
11. Tuning All Slootsmid macerators are adjusted at delivery. When changes in the adjustment occur during assembly this can be readjusted. If you have any problems contact Slootsmid. The closing tension of the cover can be adjusted by turning in or out the hinges and clamp closing. -
Page 12: Assembly And Disassambly
12. Assembly and disassembly Before you start assembling or disassembling the macerator always stop the hydro- or electro-motor and the engine of the tractor. Also take out the key and make sure no pressure is present in the hydraulic lines and no pressure of the manure is present. Then the cover can be opened. -
Page 13: Maintenance
13. Maintenance Frequently using the device: Clean the cutting-filter every day Clean the bearing house and grease the hub Exchange the bearings of the hub every year When the machine is in shelter: Clean the inside of the macerator. Remove dirt. ... - Page 14 Manure comes out the leakage canals of the hub Exchange the sealing of the hydro motor When repairing always use original Slootsmid parts, available through the Slootsmid dealers. We ask you to inform us de numbers on the rating plate when you order spare parts for your device.
-
Page 15: Attachment I: Hydraulic Scheme
Attachment I: Hydraulic scheme Non-return valve Pressure Hydraulisch schema snijfilter SF 6/ SF 8/ SF10 Blz. 14... - Page 16 Attachment II: E-motor en coupling with electrical driven macerator Aanpassen Moment Slipkoppeling: Moer rechtsom draaien = Hoger moment Moer linksom draaien = Lager moment Änderung drehmoment Rutschkupplung Mutter rechts drehen = Hoher Drehmoment Mutter links drehen = Niedriger Drehmoment Change of the torque limiter Nut clockwise direction = Increase of torque Nut counter clockwise direction...
Need help?
Do you have a question about the SF 6 and is the answer not in the manual?
Questions and answers