Page 1: Table Of Contents
Issue Date: 22/1/2020 WIRELESS MINI WALL MODULE MWMR-2300 CONTENTS 1. Overview and features Page 2. 2. Diagrams Page 3. 3. Installation – Wiring Page 4. 4. Pairing / Un-pairing device Page 7. 5. Delay Off timer setup Page 9. 6. Operation Page 11.
Page 2: Overview And Features
• Delay off timer (1M / 10M / 1H / 4H) select by trimmer resistor. • 32 memories, first in first out storage maintain. • Scene status memory, create your desired atmosphere. • 2-way switch function. Not compatible to: ARC Code switch system product range OVERVIEW AND FEATURES...
Page 3: Diagrams
Issue Date: 22/1/2020 2. Diagrams Notes for the diagrams: - Terminal for neutral wire L - Output terminal for load wire - Terminal for power supply to the switch - Terminal for live wire ⚫ Strip the solid wires (rigid conductor only) at least 7mm then connect the wires as per diagrams below, ensure terminals are properly tightened and no bare wire is visible.
Page 4: Installation - Wiring
Issue Date: 22/1/2020 3. Installation - Wiring Cut off main power before installing and wiring. Current existing house wiring should be as below. INSTALLATION - WIRING...
Page 5 Issue Date: 22/1/2020 Add mini module with one way operation 1. Connect permanent Live wire into module terminal ‘L’. 2. Connect Neutral wire into module terminal ‘N’. 3. Connect wire from module terminal ‘ L & N’ to Load. 4. Connect switch Live wire from module terminal ‘S’ into switch ‘L1’ terminal. 5.
Page 6 Issue Date: 22/1/2020 Add mini module with two way operation Two Way Operation 1. Switch 1 and 2 must be connected together with wires into ‘L1 & L2’ terminal. 2. Connect permanent Live wire into module terminal ‘L’. 3. Connect Neutral wire into module terminal ‘N’. 4.
Page 7: Pairing / Un-Pairing Device
Issue Date: 22/1/2020 4. Pairing / Un-pairing Device AIRING Pairing using LEARNING MODE: 1. Press ‘Learn’ button once (LED on module will flash), this will enter learning mode. 2. With a remote control press the ‘ON’ button; LED on module will flash to confirm that the remote control is now paired.
Page 8 Issue Date: 22/1/2020 AIRING Removing single Device: 1. Press ‘Learn’ button once (LED on module will flash), this will enter learning mode. 2. With a remote control press the ‘OFF’ button intended to be un-paired; LED on module will flash to confirm that the remote control is un-paired. LEARING EMORY Removing all memory stored in the module.
Page 9: Delay Off Timer Setup
Issue Date: 22/1/2020 5. Delay Off Timer Setup You may choose the mini module to operate normally as an ON/OFF receiver or have the extra benefit to set up delay off timer. Factory pre-setting will be at ‘0’ hour position as normal ON/OFF receiver. Set up delay off timer: ⚫...
Page 10 Issue Date: 22/1/2020 Example: 1. Adjust rotary switch clockwise to position 1m. LED on module will blink once to confirm. 2. Turn ON mini module and timer will start to count down 3. Once timer reaches to 1 minute it will automatically turn OFF. 4.
Page 11: Operation
Issue Date: 22/1/2020 6. Operation Mini module is compatible to “Self Learning” system and M series remote control. Please refer to the relevant user guide for detailed operation. Operation via Rocker Switch: Turn the load ON: Toggle switch once to turn ON load. Turn the load OFF: Toggle switch once again to turn OFF load.
Page 12: Specifications
Issue Date: 22/1/2020 7. Specifications Input Rating: 230V~50Hz Output Rating: 2300W (Resistive Load) Radio Frequency: 433.92MHz 1W Power consumption: ºC Environment Temperature: 0-40 Range: up to 50 m indoors (Depends on building materials) In accordance with: Low Voltage Directive 2014/35/EU RED Directive 2014/53/EU CE Certification: The CE marked affixed to this product confirms...