Sanyo CP29EF1 Service Manual page 11

Service Adjustments with Replacing Memory IC(IC802)
No. Item
93 VLOGIC STOP
94 VBLK TEST
95 WIDE VBLK TOP
96 WIDE VBLK BOTTOM
97 OSD CONT CLIP LEVEL
98 OSD CONT CLIP OFF
99 DRIVER (R)
100 BLUE BACK
101 DRIVER (B)
102 WHITE BACK
103 TEST PATTERN
104 PEAK ACL
105 ABCL
106 ABCL GAIN
107 DCT LEVEL
108 DCT ON
109 COLOR CONTROL PAL
110 COLOR CONTROL NTSC
111
COLOR CONTROL SECAM
112 TAKE OFF
113 C KILLER LEVEL
114 COLOR SYSTEM
115 443NT50 INHIBIT
116 FSC FREE
117 FORCE MONO
118 FORCE COLOR
129 COND KILLER EN
120 1/2FSC TRAP OFF
121 C BPF OFF
122 CTI
123 DDS OFF
124 ACC AMP ON
125 C ANGLE 95
126 RF DELAY ADJ
127 VIF SYNC ADJ
128 AFT DEFETAT
129 VIF REEQ
130 VIF VIDEO OUT GAIN
131 VIF DEFEAT
132 AFT REV
133 VIF POS
134 STRAP OFF
135 OM DET
136 VIF AGC CLIP
137 AMF ON
138 AMF VTH
Range Data Description
0 ~ 1 0 Vertical count up logic stop
0 ~ 1 0 V blanking control
0 ~ F 8 Vertical blanking top adjustment 16:9
0 ~ F 8 Vertical blanking bottom adjustment 16:9
0 ~ 3 1 Contrast control clip level of OSD mode
0 ~ 1 0 Contrast control clip switch of OSD mode
0 ~ 7F 3F R OUT amplitude adjustment by 7 bits DAC
0 ~ 1 0 Blue back mode ON/OFF switch
0 ~ 7F 3F B OUT amplitude adjustment by 7 bits DAC
0 ~ 1 0 White raster mode ON/OFF switch
0 ~ 1F 0 SCREEN TEST MODE
0 ~ 1 0 PEAK ACL MODE ON / OFF
0 ~ 1 0 ABCL ON / OFF Switch
0 ~ 1 0 ABCL Gain Low / High Switch
0 ~ 7 0 DC Transfer Level Control
0 ~ 1 0 DC Transfer select ON / OFF
0 ~ 10 0 Color Saturation control (Offset Data of Color) for PAL
0 ~ 10 0 Color Saturation control (Offset Data of Color) for NTSC
0 ~ 10 0 Color Saturation control (Offset Data of Color) for SECAM
0 ~ 1 1 Chroma BPF / Take Off switch
0 ~ 1 0 Color killer sensitivity threshold switch
0 ~ F 0 Color system selector
0 ~ 1 1 Auto color system 443NTSC(50Hz)
0 ~ 1 0 VCXO free-running mode switch ON/OFF
0 ~ 1 0 Monochrome mode switch
0 ~ 1 0 Killer function ON/OFF switch only for manual color mode
0 ~ 1 0 Condition Killer Sensitivity Enable
0 ~ 1 0 Half fsc Trap filer off
0 ~ 1 0 Chroma DDS OFF
0 ~ 1 1 Color Edge Timing Improvement
0 ~ 1 0 Chroma Bandpass Filter OFF
0 ~ 1 0 Chroma ACC AMP FUNCTION
0 ~ 1 1 Chroma Demodulation Angle switch
0 ~ 7F 2D RF AGC delay point adjustment
0 ~ 1 01 Enable VIF video out lamp
0 ~ 1 0 AFT OUT ON/OFF switch
0 ~ F 0 VIF frequency selector
0 ~ 7 5 VIF Video Detector output amplitude adjustment
0 ~ 1 0 VIF AGC gain
0 ~ 1 0 AFT polarity reverse
0 ~ 1 0 positive modulation mode
0 ~ 1 0 SOUND trap test mode switch
0 ~ 1 0 Vertical frequency standard / non-standard detection
0 ~ 1 0 VIF AGC sensitivity become low
0 ~ 1 0 VIF AGC CURRENT CHANGE ON/OFF switch
0 ~ 7 0 VIF AGC CURRENT CHANGE FUNCTION INPUT LEVEL Adj.
-11-