Eibach ANTI-ROLL-KIT AS41-55-019-01-FA Installation Instructions Manual

2016+ mazda, mx-5, nd

Hide thumbs

Installation Instructions

Eibach Springs, Inc.  264 Mariah Circle  Corona, California 92879-1751  USA  Tech Support 800-222-8811 Ext 114

Anti-Roll-Kit

# AS41-55-019-01-FA

2016+ Mazda, MX-5, ND

Kit Contents

Description

Front Bar

Anti-Roll Hardware Kit

Information Kit

Instructions

NOTES:

Read All Instructions Before Beginning Installation



Only qualified mechanics experienced in the installation and removal of suspension components should

perform this installation.



Use of a hoist and screw jack is highly recommended and will substantially reduce installation time.



Never work on or under a vehicle unless it is properly supported.



Tire Rotation: In order to increase the life of your tires, it is recommended to rotate your tires every 3,000 miles.

FACTORY FRONT BAR REMOVAL

Begin by raising the vehicle and supporting it with the

proper safety equipment, then, remove the front wheels.

Note: Never work on or under a vehicle that is not

supported by the proper safety equipment.

D3432

Photo

www.eibach.com

Part Number

AS41-55-019-01-FA

AS41-55-019-01-FAHK

EPAK

AS41-55-019-01-FAINST

Remove the left and right side inner fender covers, and

the center splash shield as shown. (See Photos 1, 2, 3

& 4)

Qty

Photo

Page 1

Table of Contents

Need help?

Do you have a question about the ANTI-ROLL-KIT AS41-55-019-01-FA and is the answer not in the manual?

Questions and answers

Summary of Contents for Eibach ANTI-ROLL-KIT AS41-55-019-01-FA

Page 1 Installation Instructions Eibach Springs, Inc.  264 Mariah Circle  Corona, California 92879-1751  USA  Tech Support 800-222-8811 Ext 114 Anti-Roll-Kit # AS41-55-019-01-FA 2016+ Mazda, MX-5, ND Kit Contents Description Part Number Front Bar AS41-55-019-01-FA Anti-Roll Hardware Kit AS41-55-019-01-FAHK...
Page 2 (See Photos 5, 6 & 7) Paint Mark Photo Unclip the wire harness from the top of the steering rack. (See Photo 11) Photo www.eibach.com D3432 Page 2...
Page 3 (See Photos 13 & 10. Loosen and remove the nuts that secure the end links to both ends of the OE anti roll bar, then, disconnect the end links. (See Photo 17) www.eibach.com D3432 Page 3...
Page 4 Note: Be careful to note the orientation of the OE bar as the Eibach bar will be installed in the same orientation. (See Photos 18, 19 &...
Page 5 EIBACH FRONT BAR INSTALLATION Driver side Photo Install the Eibach front bar into the vehicle in the reverse Photo of the removal of the OE bar. Note: Leave the poly bag on the bar as this will help to limit any scratching to the bar during installation.
Page 6 Apply some poly lubricant to the inside of the supplied Secure the end links to both ends of the bar using the Eibach front bushings, then, install the bushings onto OE hardware. Note: It may be necessary to the Eibach bar. (See Photos 29 & 30) disconnect the lower shock mount from the lower control arm in order to attach the end link.
Page 7 You can now reinstall the steering rack, making sure the input shaft and the coupler are properly aligned using the paint mark from step 4 of the removal process. (See Photos 36, 37 & 38) Photo www.eibach.com D3432 Page 7...
Page 8  Use on smooth roads and tracks.  Do not use on wet or slick roads. Photo 11. Secure the tie rods to the spindle using the OE hardware and reusable cotter pin. (See Photo 44) www.eibach.com D3432 Page 8...