Advertisement
Quick Links
Trouble Shooting for Thermal Fog Generator
For TS-35A (E), TS-34, TS-35A model,
Preface:
After fill chemicals to chemical tank, petrol or gasoline to the fuel tank respectively, install
battery to machine, the brief procedure start up machine as below,
1. Install fogging tube adapter.
2. Push down oil valve.
3. Use left hand hold air pump handle while right hand press down igniter button to
pump slowly, gently.
4. Only after heard 1 or 2 explosion sounds, pull up oil valve, then, pump a little bit
quickly will start up machine.
(Please note: If could not start up, push down oil valve, continue use left hand hold air
pump handle while right hand press down igniter button to pump machine slowly ,
Until after heard 1 or 2 explosion sounds, pull up oil valve, then, pump a little bit
quickly will start up machine, if still could not start up, please repeat this procedure.)
5. After start up, turn solution tap points to "On" position, start spray fog.
6. If want stop spray fog, firstly turn solution tap points to "Clean Solution" position,
release residual pressure inside chemicals tank.
7. Then, turn solution tap points to "Off" position, stop spray fog.
8. Push down oil valve, stop machine.
Please note: We have already fixed well the standard site of the adjust knob of the
carburetor, do not adjust it, if it is really necessary need to increase power, do not increase
more than 3/8 circle.
1. Starting up skill
1.1
Switch off
oil valve,
Advertisement
Summary of Contents for Longray TS-35A E
- Page 1 Trouble Shooting for Thermal Fog Generator For TS-35A (E), TS-34, TS-35A model, Preface: After fill chemicals to chemical tank, petrol or gasoline to the fuel tank respectively, install battery to machine, the brief procedure start up machine as below, 1. Install fogging tube adapter. 2.
- Page 2 1.2 press on igniter button, pump machine like below, 1.3 Maybe after heard 1 or 2 explosive sounds like “Peng, Peng………,” then switch on oil valve as below, Press on igniter, pump machine will start. Note: Firstly pump machine slowly, after heard explosive sounds like “ Peng, Peng…..”, then, pump machine a little bit quickly.
- Page 3 1.4 If could not start machine, please switch off the oil valve, 1.5 pump machine like below, 1.6 Then, switch on oil valve, 1.7 Then pump machine like below will start machine.
- Page 4 Note: If really could not start, please repeat the above mentioned step 1.4 to 1.7 will start machine. 2. Fix back appropriate Standard Site of the adjust knob of the Carburetor, 2.1 Adjust knob Rotate adjust knob to right direction, make “0” Scale points to “Convex”, This is the Standard Site, for starting machine or for machine working stably.
- Page 5 2.3 Reduce the power When you pump machine, please be more carefully to listen the sounds of the machine, if your heard the sounds like “ Pu, Pu, Pu……”, it means the power of the machine is too strong, you need reduce the power, Rotate adjust knob to right direction until...
- Page 6 2.4 Increase power Some time, when you pump machine, you will heard the sounds like” Bang, Bang……”, but could not start machine, you need increase the power. Rotate adjust knob to left direction 1/8, 2/8 or 3/8 circle, after each adjustment, then, try pump machine for start.
- Page 7 2.5 If still can not start up machine, check whether inside carburetor have gasoline spray out, Take out ignition high voltage cap, unscrew the 2 screws, take out swirl pole, Put finger into the hole where swirl pole have been taken out. Keep put finger into the hole, use left hand to pump air pump, then use right hand finger to feel whether if there have gasoline spray out, if do not have, rotate Adjust Knob of carburetor to increase power a little bit until finger can feel there have gasoline spray out.
- Page 8 3.1 Use screwdriver to loss the screw, take out swirl pole, making sure the two pins on the swirl pole are symmetrical. Swirl pole 3.2 Some time, when press on the igniter button, there do not have clearly ignition sounds like “Ta, Ta……”, or the ignition sounds is very low, not loud enough, please do following,...
- Page 9 3.3 You also can grind the 2 needles of the 2 sides on the swirl pole, make it shorten for 0.5 mm, it will increase the ignition electric voltage, help more easy start up machine. 4. Check diaphragm Disassemble diaphragm, clean diaphragm, spacer plates, diaphragm must clean, free of bends, cracks.
- Page 10 Then, install it back appropriately. Please note the right procedure for install back, Please note, this diaphragm must be in the middle position appropriately, if it is misplaced, could not start machine.
- Page 11 (Note: This screw should be tight, if it is loose, could not start machine, Please insert into the 3 units screw simultaneously, then use screwdriver to tighten them.)
- Page 12 Attention: (1). When install back diaphragm, please put Baffle valve on the diaphragm as following right way shows. Baffle Valve Right way (Wrong way, the diaphragm will move) (2). After install well diaphragm, please make sure the fixed plate is rightly covered the diaphragm as following picture A shows.
- Page 13 5. Check whether one-way diaphragm is properly placed? Illustration A is in gear, the one-way diaphragm is properly placed; But the Illustration B is not in gear, need fix back appropriately, if the diaphragm is broken or change shape, please find new spare parts inside spare parts kits as below to change Disassemble the one-way valve as below to check whether the one-way diaphragm is properly placed? Please check the following photos,...
- Page 14 Only photo A show the gaskets is properly placed, all the other photos is wrong.
- Page 15 Please note: Check photo below, when install back the one-way valve, only a little bit tight will be ok, please do not make it too tightly, if too tightly, the air could not get through, so the machine could not start up, 6.
- Page 16 Turn on chemical valve Turn off chemical valve Turn to left direction for turn on and increase flow rate. Turn to right direction for turn off and decrease flow rate. Note: Normally, just keep it turn on, no need to adjust it in every time for use. In 99.00% chance, this problem as below will not happen.
- Page 17 Take out the handle as below,...
- Page 18 The inside is loose, please ask us to give you the new handle of the adjustable flow...
- Page 19 rate valve, then, you install the new one to the valve. When you received the new handle, please rotate it into the hole end of the valve, Then, you use small spanner rotate the small screw into the hole lock the position of the handle.
- Page 20 After start machine, then put your hand on the chemicals tank hole to feel if there has pressure inside? 7.4 If there do not have obvious pressure inside, check following parts, 7.4.1 Check the airway pipe whether broken, if broken, please replace new one. 7.4.2 Check the one-way valve...
- Page 21 If the hole jammed, please use a thin iron wire to dredge it, then install it back appropriately. 7.5 If there have pressure inside chemicals tank, please check following parts. 7.5.1 Disassemble the bolt at the bottom of chemical tank, check the filter is jammed? If the filter is jammed, clean it, install it back appropriately.
- Page 22 Clean the pipe joint like below. Check the connected nail to find if there has deposited carbon inside, clean like below, Check deposited carbon Clean deposited carbon After cleaning, please install back appropriately. 7.6 Check whether the filter inside chemicals valve is jammed?
- Page 23 Anticlockwise direction rotation, take out the filter as below, If it is jammed, please clean it then install back appropriately. 8. When working, suddenly spray flame or fire? 8.1 Some time, customer do not install the fogging tube adapter to machine for working, it is wrong.
- Page 24 Use this clip spring to tight the fogging tube adapter to the machine. 8.2 If still spay fire, it means the power of the machine is too strong, you need reduce the power, please check below, Rotate adjust knob to right direction until to the end, for adjust back to the standard site of...
- Page 25 Use left hand to hold the adjust knob, make sure it will not move, Then use the screwdriver insert into the screw, rotate to right direction circle, check whether it will spray flame or not? 8.3 If it still spray flame, please rotate to right direction for another 1/8 circle again, now, it will definitely not spray flame.