Flowserve IPS Wireless SELD-102 User Instructions
  1. Manuals
  2. Brands
  3. Flowserve Manuals
  4. Multi-service Platforms
  5. IPS Wireless SELD-102
  6. User instructions

Flowserve IPS Wireless SELD-102 User Instructions

Single port condition monitor and wireless transmitting unit
Hide thumbs
Table of Contents

Advertisement

Quick Links

IPS Wireless™ SELD-102 Node
Single Port Condition Monitor and Wireless Transmitting Unit
PCN = 702-3001 07-17 (E) Original Instructions
These instructions must be read prior to installing,
operating, using and maintaining this equipment.
USER INSTRUCTIONS
Installation
Maintenance
Operation
702-3001^

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IPS Wireless SELD-102 and is the answer not in the manual?

Questions and answers

Summary of Contents for Flowserve IPS Wireless SELD-102

  • Page 1 USER INSTRUCTIONS IPS Wireless™ SELD-102 Node Installation Operation Single Port Condition Monitor and Wireless Transmitting Unit Maintenance PCN = 702-3001 07-17 (E) Original Instructions These instructions must be read prior to installing, operating, using and maintaining this equipment. 702-3001^...

  • Page 2: Table Of Contents

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 CONTENTS 1 INTRODUCTION AND SAFETY ......3 1.1 G ............. 3 ENERAL 1.2 CE M ....... 3 ARKING AND APPROVALS 1.3 D ..........3 ISCLAIMER 1.4 C ..........3 OPYRIGHT 1.5 D UTY CONDITIONS ........

  • Page 3: Introduction And Safety

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 Where applicable, the Directives and any additional 1 INTRODUCTION AND SAFETY Approvals, cover important safety aspects relating to machinery and equipment and the satisfactory 1.1 General provision of technical documents and safety instructions. Where applicable this document...

  • Page 4: Safety

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 there is any doubt as to the suitability of the personnel in question do not already possess the product for the application intended, contact necessary knowledge and skill, appropriate training Flowserve for advice.

  • Page 5: Transport And Storage

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 +185°F) hardware for damage. Report any damage to shipping carrier immediately. Humidity: 0-95% noncondensing Power requirement: 3.6 VDC Battery Pack Ensure you have received the correct sensors and (Part Number S1-1061) mounting accessories for your application. Cross-...

  • Page 6: Disposal Instructions

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 removed and disposed of in accordance with 3 DESCRIPTION current local regulations. The SELD-102 Node-X (where “X” designates a 2.5 Disposal instructions specific hardware configuration per order) model is a wireless transmitting unit designed to monitor one single (or combination) sensor input and wirelessly transmit the data to a receiver.

  • Page 7: Options And Model Numbers

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 system number, unit transmitter number, data transmittal/check-in interval, scale factor and offset to use with specific sensors). As long as your A complete list of the different sensors that can be specific application has been communicated to the...

  • Page 8: Performance And Operation Limits

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 Low or high alarm The battery pack is NOT re-chargeable and Each parameter has a separate low and high alarm shall only be replaced by contacting your local threshold. sales representative (Battery pack part number: S1-xxxx).

  • Page 9: Battery Replacement

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 Figure 2: IPS Node Plug 4.3 Battery replacement EXPLOSION HAZARD: The unit must be powered OFF during the battery installation & must Nuts holding be in a General Purpose Classified Area to prevent battery the possible ignition of a hazardous atmosphere.

  • Page 10: Installation

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 6 INSTALLATION There is an optional quarter turn quick disconnect that can be used to assure the orientation of the x- y-z axis is correct. This mounting configuration is Always wear appropriate personal...

  • Page 11: Connecting Sensors And Power-Up

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 6.3.2 Magnetic mount option 1. Mount flush against the end of the NPT port to measure the temperature of whatever surface it is in contact with Magnetic Mount 6.4 Connecting sensors and power-up If not already completed, install sensor on equipment to be monitored.

  • Page 12: Parts List And Drawings

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 7 PARTS LIST AND DRAWINGS 7.1 Spare parts Available spare parts for the SELD-102 Node unit are shown below. No spare parts are needed during start-up. Recommended quantities of 2-year operational spares are listed below.
  • Page 13 IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 7.2 Drawings Figure 10: Example drawing for SELD-102 Node-VA Page 13 of 22 flowserve.com...

  • Page 14: Troubleshooting Guide

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 8.1.2 Unit not configured correctly 8 TROUBLESHOOTING GUIDE To perform the diagnostic steps for this issue, the SELD-102 Node unit will need all sensors EXPLOSION HAZARD: The unit must be connected to it.
  • Page 15 IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 If none of the above solutions are successful in getting data reception at the receiver, contact the factory for additional support. Page 15 of 22 flowserve.com...

  • Page 16: Appendix: Certification

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 APPENDIX: CERTIFICATION The following certifications are applicable to the SELD-102: Model SELD-102 certifications This product must not be operated beyond the parameters specified for the application. If there is any doubt as to the suitability of the product for the application intended, contact the manufacturer for advice.

  • Page 17: Declaration Of Conformity (Typical)

    IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 9 DECLARATION OF CONFORMITY (TYPICAL) Page 17 of 22 flowserve.com...
  • Page 18 IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 Page 18 of 22 flowserve.com...
  • Page 19 IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 Page 19 of 22 flowserve.com...
  • Page 20 IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 Page 20 of 22 flowserve.com...
  • Page 21 IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 Page 21 of 22 flowserve.com...
  • Page 22 IPS WIRELESS SELD-102 Node ENGLISH 702-3001 07-17 Your Flowserve factory contacts: FLOWSERVE REGIONAL Flowserve Corporation SALES OFFICES: 10920 W Sam Houston Parkway N, Suite 950 Houston, TX 77064 USA USA and Canada Phone: +1 832 375 0807 Flowserve Corporation Pump 5215 North O’Connor Blvd.,...

Table of Contents