Advertisement

1 of 17
Original Operating Manual - German
OPERATING MANUAL U100HL-024KA-4
Micronel AG
Zürcherstrasse 51
CH-8317 Tagelswangen
Switzerland
All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the U100HL-024KA-4 and is the answer not in the manual?

Questions and answers

Summary of Contents for micronel U100HL-024KA-4

  • Page 1 1 of 17 Original Operating Manual - German OPERATING MANUAL U100HL-024KA-4 Micronel AG Zürcherstrasse 51 CH-8317 Tagelswangen Switzerland All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 2: Table Of Contents

    7 Initial Commissioning ......................13 9 Cleaning Maintenance .......................15 9.1 Inspection ........................16 9.2 Lubrication ........................16 9.3 Troubleshooting ......................16 10 Transport .........................17 11 Storage ..........................17 12 Disposal ..........................17 All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 3: Important Information

    Environmental Protection Information on the environmentally-friendly disposal of packaging materials, waste, auxiliary materials and consumables at the end of the product’s service life. All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 4: Overview Of U100Hl-024Ka-4

    A pipe or hose section of at least 12 cm in length must also be connected during operation with opened suction nozzles (suction from or discharge into the surrounding All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 5: Intended Use

    The threshold limits listed in Chapter 5, “Technical Specifications”, must be adhered to while operating the U100HL-024. Non-observance will void the manufacturer’s warranty. All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 6: Improper Use

    43,000 rpm with tolerances according to ISO 13348 Grade AN4. [Delta pressure and volume +/- 10%, power consumption + 16%, acoustics + 6dB (A)] All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 7: Mechanical Nominal And Threshold Values Of The Blower

    5.2 Mechanical Nominal and Threshold Values of the Blower 5.3.1 Dimensions Figure 1: Dimensions of the U100HL-024KA-4 in mm Pipe thread: G 3/4 inches, Thread depth: 15mm All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 8: Nominal And Threshold Values Of The Blower

    5 Sound pressure level, measured at a distance of 1 m with closed suction and pressure discharge sides 5.4.1 Materials Components Housing Die-cast aluminum Impeller Polyamide (PA6) Label Polyester All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 9: Mounting

    Damage to the electronics through the application of voltage that is too high Only operate the U100HL-024KA-4 within the voltage range specified in “Electrical Connections”. All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 10: Structure Of The Internal Electronics

    No temperature-sensitive parts, such as electrical lines or electronic components, should be in contact with or mounted on this surface. 6.1.1 Structure of the Internal Electronics Block diagram of the electronics All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 11: Pin Assignment

    Stop (Short circuit to GND for stopping)  2 VDC Minimum start voltage  1.5–5.0 VDC The blower rotates according to the applied VDC Input Resistance All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 12: Pipe And Hose Connections

    The suction nozzle is labeled with “IN”. Connect the suction line here. The pressure discharge nozzle is labeled with “OUT”. Connect the pressure line here. All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 13: Initial Commissioning

    Ensure that no foreign objects enter the fan. Make sure that media discharged into the surrounding area are not discharged close to people. All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 14 Now, increase the control voltage for the speed setpoint setting using Set Speed (0 to 5 VDC) to the desired value or the value specified in the data sheet. The working point of the U100HL-024KA-4 is adapted to the operating point of the plant using this speed control.
  • Page 15: Cleaning Maintenance

    Regularly remove dust deposits. To clean the surface with compressed air, protect the inlet and outlet nozzles from incoming dust, otherwise particles can enter into the bearings. Outside: In the case of dirt or dust deposits: Clean all surfaces of the U100HL-024KA-4. Use a damp cloth for this. Inside: The U100HL-024KA-4 is maintenance-free and must not be opened.
  • Page 16: Inspection

    Turn off fan Loose mounting screw Retighten the screw. Secure against loosening Vibrations Turbulence in the system Check air routing in the system All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...
  • Page 17: Transport

    12 Disposal The U100HL-024KA-4 is a small electrical device according to WEEE 2012/19/EU. This should be disposed of in accordance with local regulations. All data can be subject to change without advanced notice. Version: December 6, 2018. © Micronel AG...

Table of Contents